The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

What did you do to your DSM today?

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

You must be logged in to view this image or video.


before and after from cleaning my headlights

You must be logged in to view this image or video.


all dents removed and ready for paint after final sanding and a wash
 

Attachments

You must be registered for see attachments list
Chork make a gasket FTW.4th time doing this therm to head housing, and the chork holds,no leaks, besides a boost leak.F YAAAAAAA :hellyeah:

No, there's an actual gasket for thermostat housing to cylinder head, and if both surfaces are properly cleaned, a new gasket should have no problem sealing.

Told you!
 
My rail or the way i put the rail on is eating my orings..So I ordered two sets of them..I'mmmmm sooo irritated with the orings, and Im out of cigeretes.
Assuming you're talking about the fuel rail o-rings or fuel injector o-rings, it doesn't matter how you install them if they aren't designed for fuel.

I use lots of spit. :p

:dsm:
 
Trying to figure out a recurring idle issue I'm having where my O2 goes and reads 0 after driving for 30 or so seconds, intermittently.. doesn't happen all the time and cruise/WoT is pretty good. The lightest of tap on the throttle wakes it up, but it goes 0-0.03v again right after. Can't keep idle, and will stall out. I will need to start a thread on this because I'm not sure where the problem lies and I desperately need input.
 
i put them on dry..but i got the last two oring sets orileys had..im gonna put the injectors in the rail,then put them in the holes and see if putting them in was the problem..ive never had orings shread before.so it must be the way i was putting rail onto injector
 
i put them on dry..but i got the last two oring sets orileys had..im gonna put the injectors in the rail,then put them in the holes and see if putting them in was the problem..ive never had orings shread before.so it must be the way i was putting rail onto injector

Do you put in a girl dry? No. Wet the dam things and you won't rip them.
 
Installed brand new uca's.. lcas are next along with tie rod ends, while waiting for my flywheel and clutch to come in.
You must be logged in to view this image or video.
 

Attachments

You must be registered for see attachments list
Replaced my left outer tie rod and aligned it, also installed my new aluminum mishimoto radiator I got off a fellow tuner on here
You must be logged in to view this image or video.
 

Attachments

You must be registered for see attachments list
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Latest posts

Build Thread Updates

Latest Classifieds

  • For sale 2g 2G parts
    2G parts2G ignition, door locks, glove box and hatch( hatch lock doesn’t turn) comes with 1...
    • Dsm_canadian_mike
    • Updated:
    • Expires
  • For sale 2g 2G harnesses
    2G harnesses2G 97-99 under dash wiring harness MR225461 $502G front Chassis wiring harness...
    • Dsm_canadian_mike
    • Updated:
    • Expires
  • For sale 2g 1998 DSM FWD Fuel Tank
    Clean 1998 FWD DSM fuel tank
    • kyler021
    • Updated:
  • For sale 4G63 Antilag coil on plug, m&w ignition box, wilson Billet 90mm throttle body,
    I’m upgrading to fuel tech so I won’t have used for these parts I’m in the middle of a build and...
    • aguiga
    • Updated:
    • Expires
  • Wanted 1G Fuel pressure / 2G boost solenoid
    Looking for a working 1G fuel pressure solenoid. Same part was used as a boost control solenoid...
    • Drewpy Dawg
    • Updated:
    • Expires
Back
Top