What did you do to your DSM today?

[Archer Fabrications]

I might check there now thanks for the idea

Yeah man, it's huge, my holset didn't come with an o ring so i have to rtv it.

 

[Blurred Talon]

Did more wiring work yesterday.

 

[Bud92gsx]

Right, the 2g uses RTV only while the 1g calls for a gasket. You could use RTV in place of the gasket if needed. But I was always taught to use RTV or a gasket, never both.

And some of you guys need to start breaking more stuff! I can't even count how many times I've pulled the head. Hell, I built my engine before I even owned a boost controller.

Said F it and took the gasket off and used rtv.No leaks that I see.Driving the car later today.

 

[LandSpeed-DSM]

Well I think the input shaft bearings took a dump..

So last minute rush order to ShepTrans.. here's hoping that and my cylinder head get back from the machine shop in time to put her on the dyno and still make it out for the Half Mile Shootout on 6/1!

 

[SBstar]

Replaced one broken wheel stud, changed the oil (Brad Penn Green Oil of course), drained the 93 octane and filled with E85, swapped the Link tune, put in a new alternator belt, and found 6 lbs to rip out of the car. Felt like good progress

 

[Cdc1221]

Just ordered my eagles, wiseco 8.3s, arps, gaskets and timing set . Finally gonna be able to get my eclipse back on the road soon

 

[Turbomaniac18]

Put new valve lifters in. Trying to figure out why such a big gap between rockers and cams.

 

[Cdc1221]

It'll be like that until you fire it up and they pump up der

 

[combs-dsm]

well lets see. I put my new crank and bearings in. just waiting on my ARP main studs to arrive, and ported out my first and second OFH

 

[Blurred Talon]

More wiring, so sick and tired of it. Plus I can't find my good pick so depinning is being a real PITA.
Going to buy a new set tonight.

 

[my dreamt dsm]

Wash my car, detail inside, orange clean the engine bay. Oh yeah!

 

[rebellpntball]

Drove the car after 2yrs of sitting (Modding) and had my turbo seize up (cxracing 20g) oh well time for an hx35 I guess...

 

[Archer Fabrications]

Well ya, cx racing......

 

[rebellpntball]

Yeah should have known. Oh well....

 

[Cox Abele]

Finished one of the rims. I drove 14 hours round trip and paid $50 for them. The one I've refinished was the worse of them but came out great after about 4 hours of work. 3 to go!

Before

You must be logged in to view this image or video.

An example of the type of damage vs. the repair

You must be logged in to view this image or video.

Repaired

You must be logged in to view this image or video.

 

[combs-dsm]

Finished one of the rims. I drove 14 hours round trip and paid $50 for them. The one I've refinished was the worse of them but came out great after about 4 hours of work. 3 to go!

Before

You must be logged in to view this image or video.

An example of the type of damage vs. the repair

You must be logged in to view this image or video.

Repaired

You must be logged in to view this image or video.

they look pretty sick dude.

 

[Diamond Star Werks]

Finished one of the rims. I drove 14 hours round trip and paid $50 for them. The one I've refinished was the worse of them but came out great after about 4 hours of work. 3 to go!

Before

You must be logged in to view this image or video.

An example of the type of damage vs. the repair

You must be logged in to view this image or video.

Repaired

You must be logged in to view this image or video.

Those are nice rims. My brother has a set of those on His turbo lebaron. How did you repair them?

 

[Archer Fabrications]

Taking turbo off tofix a compressor cover boost leak

 

[apckofllamas]

redid my throttle body shaft seals.

 

[Archer Fabrications]

Sealed up turbo, now i wait til tomorrow to install it again. Should gain me 500+ rpm of spool.

 

[Archer Fabrications]

You must be logged in to view this image or video.

You must be logged in to view this image or video.

Little Hx40 love

 

[2slow4now]

Urbansmoker is there a part number on the 90 elbow off the housing? Right now all I have is a silicone coupler 90 but a "built for it" 90 like that would be pretty nice.

What did I do to my car today to stay on subject. Looked at it.

 

[Archer Fabrications]

I got it on the link forums by luck, they could be on ebay but it leaks if you dont have an o ring, so i siliconed one in. It's not a true 90 but a little over, maybe a 110. It still works though.

 

[Archer Fabrications]

You must be logged in to view this image or video.

It's a 3" outlet

 

[2slow4now]

Thanks. I didn't know it was a 3" outlet. I saw one on ebay before and thought about buying it. At least now I have more info on it to decide. And a part number.