1G W5M33 Bolt/slider question

[Anfurnyy]

Can anyone tell me where these 2 shorter bolts go in the mid case of the w5m33? I guess when I tore it apart I didn't pay enough attention to where these 2 went. I've tried looking at obvious places they would fit but they seem too short for everywhere and I can't find a diagram or post about it.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

Also looking for an answer as to which way the 3/4 hub slider is supposed to be orientated. I remember reading somewhere that the more tapered edge of one side is supposed to go specifically to either the 3rd or 4th gear but I can't remember which side.

You must be logged in to view this image or video.

Thanks for any advice

 

[DSMPT]

Also looking for an answer as to which way the 3/4 hub slider is supposed to be orientated. I remember reading somewhere that the more tapered edge of one side is supposed to go specifically to either the 3rd or 4th gear but I can't remember which side.

This one?

You must be logged in to view this image or video.

 

[Anfurnyy]

This one?

You must be logged in to view this image or video.

I believe so

This one?

You must be logged in to view this image or video.

What book is that? I can't seem to find anything for 3rd gear in either the training manual or the "manual transaxle overhaul" manual that I keep finding online. I see what I'm asking about for 5th gear though.

 

[1990TSIAWDTALON]

Here is my 1990 transmission rebuild picture of the 3/4 slider.
I am sorry, I can't remember which holes the short bolts go into, if I even had any that were shorter.

You must be logged in to view this image or video.

 

[Anfurnyy]

Here is my 1990 transmission rebuild picture of the 3/4 slider.
I am sorry, I can't remember which holes the short bolts go into, if I even had any that were shorter.

You must be logged in to view this image or video.

Your slider looks like the sharper angle is facing towards 3. I think I have to swap mine around

 

[DSMPT]

What book is that? I can't seem to find anything for 3rd gear in either the training manual or the "manual transaxle overhaul" manual that I keep finding online. I see what I'm asking about for 5th gear though.

This is the original Japanese factory service manual for '92 models from Mitsubishi. I sometimes see the english versions have missing info or misprint. I don't know why they skipped some part. My book has for 3rd/4th and 5th both.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

 

[1990TSIAWDTALON]

Your slider looks like the sharper angle is facing towards 3. I think I have to swap mine around

Yes that is correct. Hisroshi's picture from the service manual shows it also. I circled it in Red.

You must be logged in to view this image or video.

 

[bastarddsm]

Those short bolts don't go to the trans. And I put the sharper teeth toward 3rd.

 

[Anfurnyy]

Those short bolts don't go to the trans. And I put the sharper teeth toward 3rd.

Then I guess I'm missing a few these were all that came off this trans. I guess that doesn't surprise me..

Yes that is correct. Hisroshi's picture from the service manual shows it also. I circled it in Red.

You must be logged in to view this image or video.

My eyes must be bad. Both those angles look the same to me

I'll get it swapped around

 

[DSMPT]

Both those angles look the same to me

It shows as d < D.

You must be logged in to view this image or video.

 

[1990TSIAWDTALON]

I might have mine backwards. I can say that it shifted like butter though.