What did you do to your DSM today?

[tkrPerformance]

picked up a new turbo set up for the 89 mirage hatch

got a mhi evo 3 turbo,all lines,s.s. feed line,evo 3 O2 housing,evo 3 exhaust manifold got it all for 300.00 from a buddy

 

[turboking15]

Got the new seat brackets welded in and started fitting the new 10pt rollcage.

 

[907gs-t]

Will be repairing my block heater cord today.

 

[96DSM_Steve]

I bought a new tool to install my valves in stead of the C clamp valve spring compressor. It's Lisle valve keeper remover & installer.

You must be logged in to view this image or video.

Sent from my iPhone using Tapatalk

 

[tazndrew04]

opened the garage and thought of starting it but than i didnt and went back inside

 

[awddarrell]

Started to clean up the engine bay on the talon, progress still continues on the fuse box relocation. It is looking pretty Baron in there right now.

Took the old beat up 16g of the eclipse, in preparation for the new EVOIII 16g on Tuesday.

Took the valve cover off to replace the gasket and do a nice paint job on the valve cover on the eclipse.

 

[Flash]

I stripped the interior. Not sure what I'm up to now.

You must be logged in to view this image or video.

 

[gtbread77]

fixed my idle surge, fixed my dust cover brake squeak, kind of fixed my clutch pedal being 1.3 inches from the floor now it's like 1.8

 

[zanderson]

I wish I Could have thanked mine for starting. When I got her home I new it was going to be a project, but didn't expect to be pulling the motor. I put it up on jack stands today

 

[ViciousLord]

2 weeks ago i found black doors panels and black rear speaker panels, yesterday i found black seat belts, stock shifter, and a sunroof weather stripping... total cost 37 bucks

 

[Below Ambient]

waiting to hear from the trans shop whether its done or not, checking bank balance to get ready to drive through utah then to oregon for xmas... hopefully the dsm gods will be nice to me

 

[92AWDHX40]

Changing flat tire, working on door handle and lock, replaced isc, looked at it and said, time for another.

 

[gst96spyderman]

finished up hg repair. Harder than I expected. WHEW! Should be done compeltely by tomorrow.

 

[ilco187]

looked at it and said WTF who scratched my front bumper, got this big swipe from the middle to the driver side light, then started it for its winter warm up and was wonderin why the hell its getting super hot, turns out the rad fan is siezed.

 

[gst96spyderman]

Done... took 4 days, and outside help (timing) but its ready to boost and breathe... Please lord no leaks!!

 

[Straycat]

Realized that not only my inner trans but now my diff is making noise and I should stop driving it. I really wish tax return time would get here so I can have someone build it

 

[anthonydinatale]

Pulled it into the garage and letting all the snow dry up then I will start an pull the subframe out and I will start the por 15 to try and stop the rust

 

[92AWDHX40]

Worked on body trim, fixed window installed battery. Fixed brake pedal.

 

[deception]

Looked @ her,surfed for any place that I can get my jdm head worked on for her then logged on and typed this.I miss smashing on other cars!!!

 

[talondave]

Took off the slicks and put on the street rims and tires, so the car could be pushed around alot easier! Getting ready to strip the hole interior out and prep it for the cage!

 

[Redwidow]

I bought a new tool to install my valves in stead of the C clamp valve spring compressor. It's Lisle valve keeper remover & installer.

You must be logged in to view this image or video.

Sent from my iPhone using Tapatalk

Do you have a link, or where you bought this and the cost? Also how well does it work?
Thanks

 

[96pos dsm]

orderd aem boost and wideband for next year

 

[Army4g63]

Boosted to 25psi and drove to work...she's doin juuuuust fine.

 

[VIGILART]

took out my evo 8 560s and installed some 750s, also swapped out my 2bar gm map sensor for a 3bar free scale map sensor from ds-map. Can't wait to turn up the boost and do some tuning

 

[907dsm]

^^ I'd like to know how that turns out. I'm still on the fence big time on what em to run on my 1g. Not really worked on my dsm but I'm waiting on my EVO8 maf and bep bolt housing for my Holset FTW!!!