The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

image.jpg

Awdmonster drag car

They used to be a street car but now I'm turning it into a dedicated drag car

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

I have a drag shell that I couldn't pass up. $600 and came with the shortblock I just finished building and a 4 bolt auto rear swapped into it. How good does the small radiator cool?
AND.....how screwed up is the tube frame on the front of this? I have no idea what to do with it 🤔
I sure like your build, just asking a couple questions that I may be getting into is all. I have the rest of the front end but not sure how to attach it so I am really looking at all of your pictures ❤️
Thanks!
Marty ✌️

Screenshot_20261024_102649_Gallery.jpg


Screenshot_20261024_102637_Gallery.jpg


Screenshot_20261024_102623_Gallery.jpg
 
I have a drag shell that I couldn't pass up. $600 and came with the shortblock I just finished building and a 4 bolt auto rear swapped into it. How good does the small radiator cool?
AND.....how screwed up is the tube frame on the front of this? I have no idea what to do with it 🤔
I sure like your build, just asking a couple questions that I may be getting into is all. I have the rest of the front end but not sure how to attach it so I am really looking at all of your pictures ❤️
Thanks!
Marty ✌️

View attachment 803126

View attachment 803127

View attachment 803128
This is my first time with a baby radiator but I do plan to run M1 that should help and it’s a filled block the cooling is only for the head.

For the tube front I had mine fabricated to fit my specific needs. My advice is will this front end fit your needs ?
 
I am pretty sure this got stopped after the frame tubes were welded in so I will have to create hold downs for the fenders/hood/bumper.
Thanks for the comments and any suggestions!
Marty ✌️
 
If I can be of any help, I am here for that. Just ask, but it looks like Frank has this on track for sure! :thumb:
 
I’ll keep yall posted. Working on finishing the intercooler pipes
Exhaust
Engine diaper (engine pan)
Drag wing
Lexan install

When i get this done I’ll paint the engine bay black and hopefully I’ll have my nat fab subframe to install.

And hopefully the engine will be ready from the machine shop.
 
Got a update today it’s coming out great originally I wanted a hood exit but changed my mind to bull horn style. I was thinking condensation could fog up my window

I gotta figure out how I should mount the oil filter housing. I have a front line fab oil pump that uses a remote OFH .

att.Djpck8rmmz0JuyvDoRPfzsUmymwXuDN_d368kyAONFw.jpeg


att.j6gFqDRFUJ-wSf90efsf1kAG8P4ymbU3ykTbgHoDF2o.jpeg


att.6vJfAKW3-IEsx9Grni6jeE4DOCDF-_Ebn6U0cBwyqqU.jpeg


att.WypSrjyU7cRHm6awFc-1z-CkWs610fCBfUtYdFCpk34.jpeg


att.CYnFXE1FH9_AhmZ5qpOKP8K3utvputod7tNrx2iszaA.jpeg


att.IRtDZCcAIbNRONRnnS4TdekW6XqdSkZdV0VWOI5wyQc.jpeg


IMG_6039.png
 
Recently I had my engine at a machine shop in Chino to have the receiver groove cut. It’s been there since May, and unfortunately, I haven’t had any luck getting it done. At this point, it doesn’t look like he’ll even have time to get around to it.



Here’s where I’m at:

My block is currently O-ringed with .0625 stainless wire protruding .010. I have two options:

Have someone machine the head at least .005 to create the receiving groove for the wire, allowing me to run a copper head gasket.
Remove the stainless wire from the block, make the block side the receiving end, and install a stainless steel receiver ring in the head.

I did reach out to Armen (my tuner) for his feedback. He suggested running it as-is but switching to the thicker HKS MLS gasket, 1.6 mm (.0654”).

Ted pretty much had the same recommendation, although he mentioned that it would be a “lighter fuse.”

Just trying to get some feedback before I make a decision. I’d rather get it done right than rush into something and regret it later.

att.5doKg6mhcQ0YoL55OZqvbvmuL3OWhJySmcE0vJ5Yjjc.jpeg


att.AZaFqogne1Jq6h6Zr47uWJi_L-nlIQzFnt2dNyUpCYM.jpeg
 
I sure wish I knew someone that was experienced in doing a receiver groove but unfortunately I do not. I will be asking the FEW engine guys I know that are still around and see if anyone in Kansas (or OK, AR or MO, I am close to all) could do it. ✌️
 
Damn, since May and it doesnt look like he'll be able to get to it at all? That sucks.

Call Boostin up, they're doing a max effort 7 second setup on a stock block, see what they suggest, and where to send it? Just an idea.

Seems like a step you wouldnt want to skip, though, and just run it as is if you're looking to boost it to the moon.
 
Damn, since May and it doesnt look like he'll be able to get to it at all? That sucks.

Call Boostin up, they're doing a max effort 7 second setup on a stock block, see what they suggest, and where to send it? Just an idea.

Seems like a step you wouldnt want to skip, though, and just run it as is if you're looking to boost it to the moon.
I gotta figure this out, but I feel like at this point trying to find somebody to do. This job is going to be almost impossible and unable to do it at an accurate measurement. I might have to just run a metal head gasket against this protruding O-ring on the block on my next engine. I’ll make sure that whoever built this engine can complete the job per my request

Hiting up boostin will not be an option I’m sure he will be busy with World Cup
 
If you never ask, the answer will always be no.
Worth an email out to those heavy hitters in the industry who may be able to point you in the right direction. Good luck. Cant wait to see it come together. 🤘🤙
 
Any machine shop can do the work. Automotive or just a general industrial machine shop. The problem is essentially that you don't have a drawing. Which means you have no way to locate the orings grooves on the head. On a 4g63 the bore spacing is supposed to be 93mm or 3.6614, and as you can see the tolerance is loose- and every block is different. Now to do this you also need to have a reference point - you can use the head dowel holes. But you need to know where on your block the bores are located in reference to the dowel holes.

I could measure a block here, and work off of that. but if your block is different, then the grooves in the head do not line up with the grooves in the block.

In practice it might not be such a big deal, as maybe the tolerance of the receiver grooves is larger than the tolerance of the bore locations.

1793893868124.png
 
Any machine shop can do the work. Automotive or just a general industrial machine shop. The problem is essentially that you don't have a drawing. Which means you have no way to locate the orings grooves on the head. On a 4g63 the bore spacing is supposed to be 93mm or 3.6614, and as you can see the tolerance is loose- and every block is different. Now to do this you also need to have a reference point - you can use the head dowel holes. But you need to know where on your block the bores are located in reference to the dowel holes.

I could measure a block here, and work off of that. but if your block is different, then the grooves in the head do not line up with the grooves in the block.

In practice it might not be such a big deal, as maybe the tolerance of the receiver grooves is larger than the tolerance of the bore locations.

View attachment 803874
Thank you man you’re right ..
 
Little update on my O-ring situation.
We found out that the wire I actually have is .041, not .0625 like I originally thought. Definitely frustrating, but that’s my fault for not double-checking it.

Things should work out now that I have the BHJ O-ring tool. I’ll be able to match everything up and machine the groove in the head to properly receive the O-ring and copper head gasket.


I’ll also have an experienced machinist helping me with this since machining is definitely not one of my skill sets. What I lack in machining skills, I make up for in persistence, as he would say! LOL.


Hopefully we’re finally moving in the right direction. I’ll keep everyone updated as things progress!

IMG_6265.jpeg
 
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Latest Classifieds

Back
Top