What Intake Manifold should I use?

[crankwalker95]

Hey All! I'm new to the dsm world.. Former Honda boy growing up ..
Im looking for a good Intake manifold for my build.(street/strip)
I have a 95' GST. The block has been bored .20, Manley crankshaft, manley H beam rods, CP pistons, elim shaft kit, fluidamper harmonic balancer. Head is basically stock but with upgraded springs, retainers, seals. I'll be on 24ish psi on pump using a precision pte5862cea and tuned with AEM EMS. I could go on with mods but I think that should be enough for my question .
So, what Is a good intake manifold for my street/strip build?
Thanks

 

[96GSXDave]

All the intake manifolds mentioned above are great. Save some cash and see which one is being sold in the classifieds section! I picked up a JMF "race" intake manifold for $300

 

[98SpyderAWD]

X2 on a good set of cams... and the stock manifolds can get you to your goals... the Evo 3 is a good chocie imo.

 

[pboglio]

A vote for the RVR/EVO3 intake manifold or anything proven that is cast aluminum. I say this for one main reason, anything that is aluminum sheetmetal will burst, split, crack since aluminum has a limited fatigue life.

Minimal to no loss on the low end, nice gains up high. Quite an improvement over a stock 2g with a nice flat power curve up to 7000 rpms at least. I went back to the stock 2g intake manifold for emissions (no EGR) and I can't stand the lack of high rpm kick.

 

[mb3000]

Intake manifold dyno tests and facts only..

 

[D's GS-T]

Intake manifold dyno tests and facts only..

That test is for Evos, not DSMs

 

[born2tune]

I would recommend the magnus SMIM.

 

[mb3000]

That test is for Evos, not DSMs

The design/style of the manifold was what I was going for there. Notice the differences between the mani's that didn't preform vs. the ones that did, etc..

 

[crankwalker95]

Thanks a bunch guys!.. Im glad i joined this forum . 1st DSM so all your input has been great!

 

[gixrman]

If your going to DD this thing than I would get a 1g TB on a 2g head. Your going to feel better throttle respounce from that and make the car livable to drive over a race intake manifold.

 

[gsxeclipse97]

^^^ agreed that's why the evo3 itm is the best of both worlds.

^^^ agreed that's why the evo3 itm is the best of both worlds.

 

[G-UNIT]

These 2 are good:

4G63 Intake Manifold If you go with the hypertune make sure and buy the throttle body they offer with it.

Or the best >> JUN AUTO - JUN GT SURGE TANK

Hey All! I'm new to the dsm world.. Former Honda boy growing up ..
Im looking for a good Intake manifold for my build.(street/strip)
I have a 95' GST. The block has been bored .20, Manley crankshaft, manley H beam rods, CP pistons, elim shaft kit, fluidamper harmonic balancer. Head is basically stock but with upgraded springs, retainers, seals. I'll be on 24ish psi on pump using a precision pte5862cea and tuned with AEM EMS. I could go on with mods but I think that should be enough for my question .
So, what Is a good intake manifold for my street/strip build?
Thanks

 

[pboglio]

Um, that Jun manifold is 277,000 yen, about $3500WTF

 

[G-UNIT]

Heh, OP didn't mention price as a factor

 

[clipto]

Stock 2g or ported 2g intake manifold w/ 60mm tb is a good combr the stock 1g intake manifold is good. Also a evo 3 if you can find one. Also depends on your goal theres good people like Magnus or JMF that have really good street or race smim that you can look into.

 

[SOADweskey]

For what it's worth I have a stock 2G intake manifold that is extrude honed and I bored out the throttle body flange for a 1G throttle body. I had no problems making 450 awhp.

 

[gsxkid81]

did the op ever say if he had 6 bolt sized runners or 7 bolt sized?

 

[t-rexn8]

I'm on a stock 2g head, intake, and tb.... Putting down 500 whp

Going to do cams next.