What did you do to your DSM today?

[Bricktop]

Looked at it, as it sat on its DSM pedastals( jackstands).

 

[Bud92gsx]

I looked at too.Thought about kicking it.

 

[907gs-t]

Ordered a couple of small thing's from STM.

 

[3kgt2nv]

I have to say I took the aeromotive a1000 pump out of the box and have to say that it is a mans fuel pump. a pic on a website does it no justice

next to a 2 liter sprite bottle

You must be logged in to view this image or video.

 

[ilco187]

Got these DOHC badges off a hyundai and still trying to figure out if it looks good and where it looks good, what you think

 

[newTSIguy]

Installed my Dejon tool intake tube, and baught a fp race manifold to go with my big 16g.

 

[granite_talon]

Decided tonight to drive the 90 talon into work (27 miles) it was the 3rd time on the road. Only to have the brake pedal suddenly slam into the firewall while getting off the interstate. Made rest way to work. Found cause, left rear hard line blown out. Hard line for right side is now seeping in two places as well. Looks like I know of one more thing to add to repair / replace list. May be crimping it off if the line is not to crusty and then try to limp it home in the morning.

 

[dsmute]

ilco187 I think the badge would look awsome next to the rear wheels on either passenger or driver side towards the bottom end just above the side skirt. Just throwing an idea out there.

 

[jb2zero0six5]

Rear brake pads, new front pads still in the box. Next is transmission, transfer case and rear-end flush, and new cv shaft up front. Transfer case is leaking, along with the oil-return line. I can't get my front agx's to adjust, stuck on 1.

 

[dented_coffee]

I went to work on my 94 talon and got a text from my friend. So I went and bought another awd 1gb talon shell with 48,608 miles on it. She's been sitting next to a barn for the past 9 years. Thinking of swapping everything over as its an extremely clean shell after I gave her a bath today.

 

[tkrPerformance]

Got for free
95 awd tranny and t.c.
Bought
95 talon tsi auto fwd for the eprom,a/c,power steering,rear bumper,skirts,and tails
Bought
97 awd spyder shell for black top
Bought
97 talon front bumper for 60.00 craigs list ftw
Buying on wed
Fmic,tial o2 housing,and other parts

All to put my 98 awd spyder back together after sitting for 10 years

 

[Kyle_T]

Started my car up yesterday. First time its ran since 2002ish. Idled good, but just a little belt squeal and my stock oil pressure gauge doesnt work. So had to shut er down early and hopefully getting a new sending unit tomorrow.

 

[TheFallenJosh]

Bought a new battery and installed it, now the car starts again

 

[mchustle]

My maf sensor and/or IAC sensor decided to go out. Yay

 

[this_tsi_8urV8]

On Saturday, bought spark plugs, 2 tbolt clamps, 2 oil filters and 3qts of redline shockproof (light) fluid.

 

[DaRKSiDeGSX]

I assessed possible flood damage. All is well though, water only came to about an inch just past the doors at most. I've had up to 5 inches in the garage before.

 

[rEclipserGST]

So0o0o I went to walmart & home depot. This setup totalled around $13 I think.

Blender Bottle - $8
1/2 brass fitting - $2
3/8 brass fitting - $2

 

[Blurred Talon]

Yesterday - dyed more interior pieces.
Today - dyed my carpet and found the rest of the electronic parts for my MR2 EHPS conversion.

 

[beendenied]

So0o0o I went to walmart & home depot. This setup totalled around $13 I think.

Blender Bottle - $8
1/2 brass fitting - $2
3/8 brass fitting - $2

that's awesome

God knows my shakercup leaks after like 2 weeks, might as well put one of them to good use .

As for me, I ordered up some tein flex coilovers, and a maft gen2 setup minus a gm maf, I guarantee I can find one at a junkyard much cheaper

 

[Viggen21]

So on Saturday I decided it was time to completely strip the interior of my gst spyder. I want of to be as light as possible. All seats, panels, stereo components and whatever else I could find. I realized that there is a lot more I can take out but don't want to risk removing something that is critical to the car driving properly. Any ideas on how to take out the convertible top motor, rear seat belts, power antennae and passenger side airbag without causing any unexpected errors?

 

[beendenied]

So on Saturday I decided it was time to completely strip the interior of my gst spyder. I want of to be as light as possible. All seats, panels, stereo components and whatever else I could find. I realized that there is a lot more I can take out but don't want to risk removing something that is critical to the car driving properly. Any ideas on how to take out the convertible top motor, rear seat belts, power antennae and passenger side airbag without causing any unexpected errors?

I personally wouldn't strip my car unless it was a straight up tow to the strip/track to race. I just don't see the point, it's not going to affect dd quickness very much, idk just my opinion. I would help you out on removing but I've yet to tear into a vert.

And I like to listen to my stereo while I drive.

 

[EDM95]

So0o0o I went to walmart & home depot. This setup totalled around $13 I think.

Blender Bottle - $8
1/2 brass fitting - $2
3/8 brass fitting - $2

That's better than that gator bottle you had.

 

[sayaovang dsm]

hmm, i didnt do anything to my dsm today, because ive been crying about losing it for almost a year now! but its ok ill be getting another soon!! i hope though i have no cash!!! so ill be rocking the starquest until i can save money for another dsm!

 

[Blurred Talon]

Didn't notice the post above mine, I hope that bottle doesn't melt.

Oh, I have purple hands now, freaking RIT dye.

 

[Lizardman]

I cleaned out all the gunk around my pulleys and timing belt