The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

Post a Question

What did you do to your DSM today?

Please Support STM Tuned

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

92 awd laser said:
I have seen this on alot of sites with mustangs, hondas, volkswagen, ect... Although I've never seen one with DSM's and i thought maybe i would try it out and see if it sticks... I'll start off with what i did to mine. I cleaned up the motor bay and did a little wire tucking.
Click to expand...
Called STM and tried to get my money back LOL
 
Parts back from powdercoat 😁. Figuring out what bolts I need for the volk arms and a few other odds and ends started mounting ebrake cables and brake lines.

You must be logged in to view this image or video.


You must be logged in to view this image or video.


You must be logged in to view this image or video.


You must be logged in to view this image or video.


You must be logged in to view this image or video.
 

Attachments

You must be registered for see attachments list
Boosted92rs said:
Parts back from powdercoat 😁. Figuring out what bolts I need for the volk arms and a few other odds and ends started mounting ebrake cables and brake lines.


You must be logged in to view this image or video.


You must be logged in to view this image or video.
Click to expand...
Personally I would never coat a flange mating surface, powder doesn't always apply evenly and you can see it builds up around holes.
 
Freakin' stoked. These seem like boring pictures, but these mark the end of months of scavenger hunts and long car trips. The interior is finally 100% complete!!

You must be logged in to view this image or video.

You must be logged in to view this image or video.


These are MINT too.

Also finally bolted the VC down and got it all buttoned up with the spark plug wires!

You must be logged in to view this image or video.

You must be logged in to view this image or video.


It's getting so close now. Just a few odds and ends, definitely need to go through and detail clean and paint the engine bay..but then it'll be time to start, break it in, and do some rips!
 

Attachments

You must be registered for see attachments list
You must be logged in to view this image or video.

You must be logged in to view this image or video.


Was sent this by @saturn345 and I couldn't be more stoked. I loved these back in the day, and still do. Cleans up the engine bay a lot!!
 

Attachments

You must be registered for see attachments list
Finally started the remote mount of my fuel pump relay. It's going under the antenna. Waiting on a couple of things from RTM and then the ACT flywheel is going on.

The Jacks Trans rebuild will be going on sometime in the near future.
Need to add resistors for the LED light conversion.

SixBolt_16G said:
Hey all,
Probably a super basic question and not what worth starting a thread about, but what is this?

You must be logged in to view this image or video.


I was looking through some threads last night and found a picture of someones engine 6(bolt swapped 2g) that has the same piece that I came across on my car when i was putting my intercooler piping in.and have no clue what it is...
Click to expand...
The item circled looks like the ignition power transistor. That's what sends voltage to the ign. coils.

CrackedDSM said:
Scored a set of sunvisors from Nate at performance part out. They’re in fair condition. Considering how hard these are to find, just the fact they have fabric on them was more than enough for my to pull the trigger. I bought them like minutes after he listed them on his website. Lol.

But, I bolted them up today. This was one of the last pieces of the puzzle. Now I just need that damn passenger side b pillar trim!

You must be logged in to view this image or video.
You must be logged in to view this image or video.
You must be logged in to view this image or video.
Click to expand...
Funny...I just got a set of sun visors from him not too long ago.
 
Brought her in the garage for maintenance before I start the other side rockers and quarter panels, in a time crunch for a paint Job , let's see if it actually gets done this year LOL

You must be logged in to view this image or video.
 

Attachments

You must be registered for see attachments list
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Boosted Fabrication
ECM Tuning
ExtremePSI
FIBA Motorsport
Fuel Injector Clinic
Innovation Products
Jacks Transmissions
JNZ Tuning
Kiggly Racing
Morrison Fabrications
Rix Racing
RockAuto
STM Tuned
Support Vendors who Support the DSM Community

Latest posts

Build Thread Updates

Vendor Updates

Latest Classifieds

  • jersygsx
    For sale 2g 2G DSM Link V3
    2G DSM Link V3 $600 + shipping and paypal fees* no cable included * cables are 75 on the...
    • jersygsx
    • Updated:
    • Expires
  • frosh29
    Wanted 2g Shot in the dark (2g Pass strut cut out)
    Need 2g strut tower to save time.
    • frosh29
    • Updated:
    • Expires
  • jersygsx
    For sale 2g 2G Mishimoto Radiator & Fan Shroud
    2G Mishimoto Radiator & Fan Shroud $200 + shipping and paypal feesYou must be registered to...
    • jersygsx
    • Updated:
    • Expires
  • The_Partout_Spot
    For sale VIRGIN 4G63 6-BOLT TURBO HEAD
    Came off a virgin stock AWD Auto 1G DMS (91), also have matching block and crank which are also...
    • The_Partout_Spot
    • Updated:
    • Expires
  • The_Partout_Spot
    For sale 1G DSM 4G63 6-BOLT TIMING COVER
    Used, see condition in photos. Buyer covers shipping / fees.
    • The_Partout_Spot
    • Updated:
    • Expires
Back
Top