We're on Boost said:

No, 11mm is the OD of the outlet pipe. Depending on where you look, the outlet pipe is either given as 11mm OD or as 3/8" Hose barb. It's made for 3/8" hose. Nobody gives an ID for it.
1g users in here have been putting 3/8" hose on it. Take a look at Marty's pics here in post #278. In the first pic you can see (barely) that the hose says 3/8" and 9.5mm.
So yeah I don't know how all this would work out on a 2g. It's so crowded vertically.

Click to expand...

It seems I miss calculated the inside diameter, I always have to convert to mm.
I'll buy one of this adapter, I've seen them on STM or Extremepsi website and once I have the pump out i'll try it. If I can keep the same length of the whole assembly then it's definitely a better option.

We're on Boost said:

In here it's usually agreed that the AEM stainless MAP sensors are the best ones and the most reliable. They are round barrel type.
3.5 bar if you aren't going to go over 35 psi of boost.
5 bar if you are going higher than 35 psi boost.

I've used them both. Lately I have the 3.5 bar on my car because I noticed I was getting spikes on my AFRatioEst plots in the logs. Didn't notice any bad behavior from it though. Anyway there's no spikes with the 3.5 bar.

Click to expand...

AEM it's an option but I'm not sure what boost I will run so I can't say if 3.5 bar it's enough or not. I would say a 4 bar sensor would be the smart choice.

CDgr97GSX said:

I would say a 4 bar sensor would be the smart choice.

Click to expand...

4-bar is kind of the ideal range, true. I wish AEM made their sensor also as a 4-bar.
If I had to buy a 4-bar here in the US, I would get the one sold by Ballenger.
They are as far as I know the only place that comes right out and says that the "genuine" GM type MAP sensors sold these days are lousy quality because of excessive cost cutting and moving production to low cost facilities.
The writeup they have for their 3-bar has this info in the Description.
The only actual experience I have with it though is the Ballenger 3-bar that OhhShmit put on his car about a year ago, and it's fine.
And of course the Un-genuine cheapo (like $20) GM sensors are usually not good either, I mean some of them might be accurate at first but then not last very long.

As far as I know, the OmniPower ones were good up until about 5 or 6 years ago. I had one on my car that was new in 2016 and it never failed, I just took it off preemptively because I hate roadside emergencies and that's what we started hearing from people. So I bought an AEM 5-bar in 2021, then bought the AEM 3.5-bar in 2023 and hope to be running that forever. All 3 of the MAP sensors I have had were remote mounted, not directly attached to the engine. That helps.

I checked the AEM 3.5 bar sensor and honestly I don't like it so much, I have to use 2 adaptors and on top of that I have to do the wires too.
Omni power is plug and play

CDgr97GSX said:

I checked the AEM 3.5 bar sensor and honestly I don't like it so much, I have to use 2 adaptors and on top of that I have to do the wires too.
Omni power is plug and play

Click to expand...

Yes the physical mounting and electrical plugs are completely different. Same 3 wires but different connector on the end.

CDgr97GSX said:

Omni power is plug and play

Click to expand...

You can get another but expect to have to replace in the future.

Eh my brain wasn’t working, this is a pump for the front wheel drive. It’s an aftermarket copy of the original but it uses a barb style fitting for the pump. I’m not sure how or if the gsx pump is different

I'll go with AEM 5 bar. It's a good price on Amazon

chrysler kid said:

Eh my brain wasn’t working, this is a pump for the front wheel drive. It’s an aftermarket copy of the original but it uses a barb style fitting for the pump. I’m not sure how or if the gsx pump is different

Click to expand...

Ok thanks!

CDgr97GSX said:

I'll go with AEM 5 bar. It's a good price on Amazon

Click to expand...

Should be good! I bought mine from Amazon too.
30-2130-75 right?
Here I see "Free delivery Wednesday August 26".
Do you have to wait longer or pay extra shipping for it over there?

We're on Boost said:

Should be good! I bought mine from Amazon too.
30-2130-75 right?
Here I see "Free delivery Wednesday August 26".
Do you have to wait longer or pay extra shipping for it over there?

Click to expand...

Unfortunately this one it's not possible to get it to Romania from Amazon.I have the option to deliver it to a friend in CA. He will help me out with shipping to my address. Instead the Omni Power have the option for international shipping and it will cost like 20-25 $ extra in shipping and fees.

CDgr97GSX said:

Unfortunately this one it's not possible to get it to Romania from Amazon.I have the option to deliver it to a friend in CA. He will help me out with shipping to my address. Instead the Omni Power have the option for international shipping and it will cost like 20-25 $ extra in shipping and fees.

Click to expand...

Oh man, kind of a pain!

We're on Boost said:

Oh man, kind of a pain!

Click to expand...

Yeah, I've done this with all the parts i got so a sensor it's the easiest part so far.
Anyway I've changed the plan, I got the sensor from a dealer in Europe, it's a little bit more expensive at about 200 € shipped to my address but i'll get it in few days.