Recently I had to pull my head because of leaking valve stem seals causing me to burn oil and since I’m running a fully exposed timing belt I was wondering if it’s at all possible to have a non interference set up If I use a thick enough head gasket and how thick do I need to go.The oem cams...

I’m looking for a cost effective valve kit package and I found this on eBay… can anyone confit that these will in fact fit a 6 bolt head? The Hyundai part threw me off a bit.

Those of you who have cleaned the inside of your block while its out. What was your process and how successful was it?I pulled my motor to build it and its really dirty, plus i did some grinding for the Kiggly Girdle install, and ive done the porting/smoothing of the front oil passages on the...

Hi this is my first time learning how to work on a car and when trying to remove the head I couldn't find a socket or which socket I needed to use. I also checked online but could not find it. Does anyone know what the 4g64 Head Bolt Socket and size is? Thanks.

Hey Everyone, Long time no see! I havn't touched my poor 97 Talon TSi in 3 years and i finally got the cash to rebuild my head so I'm seeking some advice after I've read through a couple of the forums here.Background Story: A few years ago my valves smacked my pistons so i had the head...

Ok so I have all of my timing marks aligned correctly. I am trying to install the belt but it does not have enough slack, I have the tensioner pulley completely lose and the grenade pin still inserted in the auto tensioner. I followed the vfaq for correct routing and that does not work. All my...

Just got my new seals and valves installed, got water sitting on the valves to see if any leaks exists. After that I'll install the BC268/272 cams shafts and cam gears. Everything went smooth and I used the K-motors compressor tool, it was only $50.

So I ordered new valves, seals and some 268/272 BC cams for my head. My current cam gears have the timing adjusted slightly with the stock cams. I know I need to retune after installing the new cams, but should I leave cams how the currently are or set them back to 0?

So I think to get the experience I am just going to go ahead and rebuild my head myself. I'm not looking to do anything fancy, my car is around 320WHP and I only need to replace my exhaust valves but I figure while it's all out what are other things that should be done.Also if you could...

Hello all,I have noticed my car is consuming coolant since switching to the Hx35 / E85 setup. Others have mentioned they see a spray from under the passenger side during a pull, my coolant overflow is on the passenger side of the car. Initially I assumed it was a head gasket issue. This past...

This build is into it's forth year and thousands of hours in mech time with only a handfull of kills DAMMIT! : )Whats the problem and description?Our 1g streetable 5sp to auto converted grudge race drag car, still has a bunch of JNZ parts on it, including the jmf race mani, Kelford 280s...

Okay, you get the picture, running a 1G NA TStat housing on a 7bolt. What thermostat do I run?

After doing some searching on here I'm thinking it might be a balance shaft, bearing, or tensioner going bad. The noise can be described as either light grinding or a rapid rattle. It's definitely localized near the timing belt area, at first I thought it was coming from under the valve cover...

Briefly searched to no avail. Friend of mine and myself are looking at putting Walbro 450’s in the tanks of our ‘95 Talons. We’re using the stock hangers and I realize this is an easy job.However, I’m pretty detail-oriented (anal) and STM’s bulkhead fitting is 5/16” to 6AN and by looking at...

Up for sale is a super clean 4G63 2G head. I decided to stick with my 1g head instead. $265 obo. Comes with everything you see pictured. Does not come with cams or valves. For more photos check out my google photos link: https://photos.app.goo.gl/ywPLW48h5H4nnz6s9 Feel free to PM me here or text...

I am now in possession of 94 talon ES it has vacuum leaks needs a new head needs the tank dropped and a new fuel filter where can i get a head that wont murder me cash wise , im 16 and my local pick and pulls wont let me in.

Hey all,For starters - I'm motivated to get this beast gone. Looking to move all of this as soon as possible!You're welcome to take the whole car and then some (as in, everything in my storage unit with regard to it) - includes what you’ll need to put the car back together and a bunch of...

Still have alot of stuff to sell. All prices are OBO, and none of them include shipping and p/p fees. I only accept paypal or cash. Shipping will be fedex or USPS. PLEASE ADVISE, if you specify USPS and you do NOT pay for insurance then I am not liable for damages. Recently had a member get a...

Was purchased for a replacement, but was never used. $250.