The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

FB_IMG_1751294680936.jpg

Street Build 1g build - The Real Life Trials and Tribulations of building a DSM

Stock 14b,--> PTE 5031--> FP Red --> GTX 3584RS build 1GB --> 1GA chassis swap

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

I would double-check the efficiency of your fuel pumps. If I remember correctly, there are two versions of the pumps, a high-pressure and a low-pressure version. Since you’re running a dual-pump setup, make sure both pumps are functioning properly and keeping up with the demand at high boost.


The reason I mention this is that I had a similar issue with my car blowing head gaskets. In my case, the fuel pump was losing effectiveness under high boost and high base fuel pressure. It’s worth checking your fuel pressure under load before ruling out a fuel delivery issue.
I'll double check my fuel pressure as it's logged in my ECU.
Thanks for the heads up!
 
So what's everyone go to for valves for high hp cars?

I run almost exclusively e85 and flex fuel is really just there in case I ever find myself in a position that I need to run 91 or 93. So I'm not sure I NEED the super alloy.

I'm looking to either move to some full set of GSC valves with their regular intake valves, and their Super Alloy exhaust valves

Or

Keep my Ferrea 6000 intake valves but step up to Ferrea Competition Plus exhaust exhaust valves.

New head will get new GSC guides and we'll see if they can reuse the seats.
 
So what's everyone go to for valves for high hp cars?

I run almost exclusively e85 and flex fuel is really just there in case I ever find myself in a position that I need to run 91 or 93. So I'm not sure I NEED the super alloy.

I'm looking to either move to some full set of GSC valves with their regular intake valves, and their Super Alloy exhaust valves

Or

Keep my Ferrea 6000 intake valves but step up to Ferrea Competition Plus exhaust exhaust valves.

New head will get new GSC guides and we'll see if they can reuse the seats.
I’m running stainless steel intake valves and inconel exhaust valves. Supertech
 
Got the oil pan off yesterday and popped off rod caps and bearings for 2&3 since they were at the bottom.
3 looks a bit more beat up. There's a few small gouges in 3 on the rod side as well as a little more wear but personally with this being time really pulling bearings nothing terrible IMO. I could just be ignorant. I do know you don't want anything other than normal wear. The crank journals look healthy and gougeless.

2 & 3 PXL_20261104_234436678.RAW-01.jpg


2 PXL_20261104_234439194.RAW-01.jpg

3 PXL_20261104_234442845.RAW-01.jpg

Some sort of "pitting" or something. On the rod side of both 2 and 3 maybe from cavitation?
PXL_20261104_234702741.RAW-01.jpg

Going to try and pull 1 & 4 tonight or tomorrow to see how those look. Ill get new bearings on order regardless.

Shift rail end is on its way back from Kurt @ White Shed, then all the stuff is getting boxed up and getting sent to Tim. Hopefully it'll be sent off before the end of next week but we'll see.
 
Shift rail came in today. Nice piece for sure!
With that all the pieces to the puzzle are here and the trans is ready to ship.
PXL_20261109_230218112.jpgPXL_20261109_230221108.jpgPXL_20261109_230223899.jpgPXL_20261109_230227583.jpg

Got it all boxed up real good. Definitely not going anywhere. I even flipped it on its side and it didn't move. Total weight is about 130lbs
PXL_20261109_233904937.jpgPXL_20261109_235206873.jpgPXL_20261109_235209725.jpg

Last time I'll see this trans for a few months 🥹.

Gonna be one hell of a unit when it comes back!
 
Last edited:
Trans dropped off at UPS. 137lbs 😬

Tim says he's got easily 5-6 months of trans work to do currently so it'll be awhile before I see that thing again. But damn I'll be excited when it comes back!

I guess now I work on some less important stuff. Gotta swap out some rod bearings and work on getting the new head rebuilt.

Keep you guys posted
 
Tim received the transmission last night. Had a little scare where they delivered it to the wrong freaking building.

Luckily Tim was able to find it and get it back home. Verified that everything was intact and safe!
Now the wait begins!

Got rod 1 and 4 caps and bearings out last night as well. Pretty much more of the same as 2 and 3. 4 looks like something decent sized went through.
PXL_20261118_233144259.jpgPXL_20261118_233151835.jpg
Honestly it kind of makes me want to pull the whole engine out and throw it on the stand and check over the mains. I don't see anything wrong with the rod journals on the crank but pitting in the bearing makes me question what is going on in there. My main clearance was also a little large from what I remember so I COULD give me the opportunity to fix that as well.

Black Friday deals are up at extreme psi so I took advantage of that and ordered up some head stuff.
• New Ferrea 6000 exhaust valves
• +.0001 clearance rod bearings
• new keepers
• new valve seals
• new GSC bronze intake and exhaust valve guides.

I'm contemplating counter drilling the holes for these washer inserts myself because the last shop I had the head at wasn't able to do it in house (odd) and sent it out to another shop to do.
 
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Build Thread Updates

Latest Classifieds

Back
Top