2G Transmissions help

[Brettmclayto]

ok I’m going to word and use pictures to explain my issue the best that I can. Tonight I just put a new clutch in. After installing I noticed my clutch fork is properly adjusted in the middle but will only move in one direction. Is this right? The slave should push it in the direction that it won’t move.

Idk how to even word this. I’m pushing on the fork but it won’t go anywhere

 

[pauleyman]

Hehe...yeah you arent going to move it with your finger. The second pic,it will stop when the throw out bearing is touching. It's fine.

 

[Vegas Smith]

But some muscle on those baby fingers and then you'll move it

 

[Brettmclayto]

Hehe...yeah you arent going to move it with your finger. The second pic,it will stop when the throw out bearing is touching. It's fine.

This will be my first time doing this, I appreciate all the help and the reply’s.

So you’d be safe to say everything is correct? I’m guessing the slave has a ton more power then my finger and will be able to move it

 

[Brettmclayto]

But some muscle on those baby fingers and then you'll move it

But I’m just a little b*

 

[Brettmclayto]

Also noticed my new clutch, the teeth on the plate that get 14ft with the bolts. The teeth are flat? Are they suppose to be coned out?

 

[pauleyman]

Also noticed my new clutch, the teeth on the plate that get 14ft with the bolts. The teeth are flat? Are they suppose to be coned out?

They were coned out. They flatten out when you tighten the bolts down. That is the pressure plate by the way.

 

[Brettmclayto]

They were coned out. They flatten out when you tighten the bolts down. That is the pressure plate by the way.

Thank you for the help, I’m trying to put something together I didn’t take apart. It’s been a rough 8 months doing it.

I do have this bolt I have no idea where it goes It has some paint on it.

Some fluid runs though but like I said I didn’t really take this car apart

 

[Brettmclayto]

Thank you for the help, I’m trying to put something together I didn’t take apart. It’s been a rough 8 months doing it.

I do have this bolt I have no idea where it goes It has some paint on it.

Some fluid runs though but like I said I didn’t really take this car apart

 

[Brettmclayto]

If anyone wanted to see this project

 

[pauleyman]

Thank you for the help, I’m trying to put something together I didn’t take apart. It’s been a rough 8 months doing it.

I do have this bolt I have no idea where it goes It has some paint on it.

Some fluid runs though but like I said I didn’t really take this car apart

That's a banjo bolt. Turbo has some for both oil and water and fuel filter has one assuming this thing is stock.

 

[chrysler kid]

That's a banjo bolt. Turbo has some for both oil and water and fuel filter has one assuming this thing is stock.

Its probably the bolt for the slave on the trans. The turbo banjos are smaller

 

[pauleyman]

Its probably the bolt for the slave on the trans. The turbo banjos are smaller

Forgot about that one. That's probably right.

 

[Brettmclayto]

That's a banjo bolt. Turbo has some for both oil and water and fuel filter has one assuming this thing is stock.[/

Forgot about that one. That's probably right.

Thank you for the advise. Where would this banjo bolt go on the slave? I’m not home at the moment to get an idea on where it would even go.

 

[pauleyman]

Where hardline connects.

 

[Brettmclayto]

Where hardline connects.

Ok Iv check and the bolt for that is there. Iv checked the fuel filter. All the ones on the turbo. I’m not really sure now

 

[pauleyman]

You sure its not just an extra? New slaves sometimes come with new bolt .

 

[chrysler kid]

Like this

You must be logged in to view this image or video.

 

[Brettmclayto]

Like this

You must be logged in to view this image or video.

Yes sir! It looks just like that on mine. It can’t be an extra, It came off the car somewhere. It’s labeled a 7 on harness if that helps.

I’m still not done putting it togeather but I wouldn’t like to start this thing without knowing where it goes.

I see only 2 banjo bolts on the turbo.

I’ll take some more pictures tomorrow.

 

[Brettmclayto]

I did get this thing in the car today.

 

[Vegas Smith]

Nice, most of the work is done.