The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

Sacramento Raceway CA 7/31

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

There's going to be other dsmers out there that have a 10 minute drive from a hotel that will hopefully help hold down a spot. I don't think there is going to be a rush to get in line at 730 am. Lets have a vote.

All in favor of leaving san jose at 6 am say I
All in favor of leaving san jose at 5 am say I Suck

"I"
 
I am not trying to leave at no 5a.m., its not a weekday.LOL Im probably going to stay the night in the valley, and leave at like 6. Anyone in the valley going Sunday? Modesto, Stockton, Tracy area? Lets meet up! At a mcdonalds...LOL
 
Oh yeah! I still have the potentiometer in my kit, just in case. :thumb:
That was a nice fix. The car drove normal the whole way home.

your heater get stuck all the way on or something? the only thing I can think of that you could use that for is that old school resistor in your IAT maf wire thing to lean out your car.

"Micky D's, open at 5 am so you can have an unfeasibly shitty start to your day."

anyone who wants to buy something from me at this meet, let me know ahead of time and I'll give you 20% off the price listed on my thread(s). I really want to clean out my garage and don't like to throw stuff away.
 
your heater get stuck all the way on or something? the only thing I can think of that you could use that for is that old school resistor in your IAT maf wire thing to lean out your car.
The wires going into the coolant temp sensor were going bad again. It finally got bad enough that I could see ECT dropping and spiking on the logs by over 100* difference. Ted says, 'I got a 10k pot in my kit', and that was all it took. We cut the wires going to the coolant sensor, attached the pot, adjusted it until the logger showed around 175* and left it there. :hellyeah:
 
The wires going into the coolant temp sensor were going bad again. It finally got bad enough that I could see ECT dropping and spiking on the logs by over 100* difference. Ted says, 'I got a 10k pot in my kit', and that was all it took. We cut the wires going to the coolant sensor, attached the pot, adjusted it until the logger showed around 175* and left it there. :hellyeah:


And I think you went on took home something at the event as well :thumb: Im still waitin on that beer btw, its gonna be hot up there...green bottle XX , bud lite lime, or coronas are good with me :sneaky:

Works been kickin my ass this week, I still gotta put my car back together! WTF
 
Hey Ted what time are you going to get out there?? I want to see if I can meet up with you guys out there and I think my buddy want to run the gto out there
 
Sorry i've missed quite a few posts but i'm assuming most of you are speaking about Sun not Sat correct?

I'll be cruising out from Hayward around 7-8am.

Keep an eye out for the po-po on I-80 if you travel that route even on a Sun morning ;)
 
Sorry i've missed quite a few posts but i'm assuming most of you are speaking about Sun not Sat correct?

I'll be cruising out from Hayward around 7-8am.

Keep an eye out for the po-po on I-80 if you travel that route even on a Sun morning ;)

Yes alot of us are talking about Sunday. As for the cops I think they'll be more focused on the DSM's than the one hybrid haha
 
Hey Ted what time are you going to get out there?? I want to see if I can meet up with you guys out there and I think my buddy want to run the gto out there

Im leaving here tomorrow evening around 5 or 6. I need to catch some zz's saturday cause I work at 4am monday morning. Sunday is gonna be a LOOOOOONG day :|
 
Well fellas guess I'll be seeing some of you at Sac but unfortunately I wont be running. I overheat way to fast at idle with this new setup and no shields.
On the other hand, my Talon will be at a vendor booth for Midnight Performance. Not that I've ever gotten any work done by them, as a matter of fact, everything has always been done at my house or my buddy's house. My buddy runs that shop so he asked if my car could be in their booth. They do all kinds of custom work n all too. Anyways, I'll see you all on Sunday and good luck to those of you running.
 
Projekt what time you leaving? Ima be in modesto tomorrow for a bully show then heading to sac on sunday. Maybe we can roll together?
 
Projekt what time you leaving? Ima be in modesto tomorrow for a bully show then heading to sac on sunday. Maybe we can roll together?

Its still in the air but I'm thinking around 7am Sunday would be good or maybe earlier. However, I'm still undecided whether to leave Saturday night to spend the night at my buddies or just wait to leave on Sunday. I'll post up tomorrow.

Either way, yea it'll be nice to follow someone since I've never been there:shhh:
 
I will be leaving this afternoon:D I heard through the grapevine they are possibly having a lil "import vs. domestic" shootout tonight and I also want to get some test passes TONIGHT when the air is cool:hellyeah: Its going to be a EPIC weekend guys!!!!!!See all of you out there.Come by and say hello!Ya'll drive safe!!!!
BTW for those of you who dont know........I have a white Galant VR4 it has a cf hood and gold wheels.
PEACE
 
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Build Thread Updates

Latest Classifieds

  • For sale 4G63 1g/2g Auto Welded Center Diff
    1g/2g Auto Welded Center Diff. Message 702-741-6987.
    • Galant665
    • Updated:
  • Wanted WTB MSD DIS 2 bypass plug
    As the title states.You must be registered to see element.
    • ist dwa
    • Updated:
    • Expires
  • Wanted ISO Extreme Psi weighted shift knob
    Easy peazy…
    • James92
    • Updated:
    • Expires
  • For sale 1g 91-94 ignition coil
    1g coil with harness side igniter harness. Digging in a box of remains from a yard six bolt for...
    • Galant665
    • Updated:
    • Expires
  • Wanted 2g Finish My Project!
    I am in need of some big ticket items in order to finish my project. In my engine bay there is...
    • dhssoccer24
    • Updated:
    • Expires
Back
Top