NEED someone with SAFC camera and screwdriver!

[darkiller_666]

Someone broke into my car and ripped my SAFC out. I still have it but the wires are ripped out of the box. If you screw the back of it you can see a lil black piece that all the wires connect to then it connects to the board. I need a picture of what order the colored wires go into the black piece. If someone could snap a picture so i could rewire it id appreciate it very much!

 

[sparco431]

i dont have a pic, but to give you some advice based on experience. go out and get a alarm and wire it up. after you do that your car wont get broken into. my car got broken into alot before i got my viper alarm, and after i got it noones even dared to go near it. once the b****s see the led blinking they'll get scared. for some reason eclipses are one of their fav cars to break into

 

[darkiller_666]

yeah i have an alarm with remote door poppers and the whole 9 yards! its on the list to be put on also, i have a diagram to wire it tho just not for the SAFC! ANY HELP ANYONE? thanx in advance

Is there a diagram on the net anywheres or neone willing to help me out here?

 

[z24frank]

Id get ahold of a vendor or contact them directly and ask them to e mail you a diagram.

 

[darkiller_666]

It wouldnt take but 2 minutes to screw the back off and take a picture of the wires! Im not to sure which vendor i would try to contact to obtain a inner wiring diagram. They keep sending me how to wire it to ## ecu.

 

[smokem]

I can open up my SAFC II, but i assume you need a pic of the 1st gen SAFC?

 

[darkiller_666]

Yes mine is the 1st gen. Would the wires be the same? I should have the talon running again by the end of the week and would like to get it all put together before i start driving it. i dont think its a good idead to just leave all the wires hanging out either.

 

[djmixerx]

I believe the 1g and 2g AFC wiring are pretty much the same. The only difference is that the 2 has a extra wire for knock.

 

[darkiller_666]

I would greatly appreciate a picture of either. anywhere i can start. With the back of the Safc screwed off, there is 2 chips inside. One chip comes off and has a black piece that all the wires go into. That is the piece all my wires are ripped out of.

 

[smokem]

I don't know if they are, probably not but here they are anyways.
Brown wire is the top.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

 

[darkiller_666]

thank you so much for the pics im gunna check tomarrow and see if there close! if anyone can just snap a pic of a safc1 thats be awesome also! Your piece isnt even black like mine!

 

[darkiller_666]

Which wire is for the knock sensor? Itd be awesome if someone could get a pic of a SAFCI!

 

[darkiller_666]

You must be logged in to view this image or video.

You must be logged in to view this image or video.

You must be logged in to view this image or video.

[/QUOTE]


need this same thing from an SafcI

 

[smokem]

I don't know what the inside of the SAFC looks like but i can tell you this, the other end that plugs up to the signal wire harness are in the same order that they are in the pic i posted? Just an assumption but i could be the same way with yours.

 

[darkiller_666]

the other end that plugs up to the signal wire harness are in the same order that they are in the pic i posted?

I see what you mean by this i feel stupid for not thinking of this myslef thanx for the help

 

[smokem]

What i mean is the other end of the wire that you see also has a plug on the end of it that goes to the signal wire harness. Well the harness on the other end has all the wires in the same order. So if its the same on the SAFC as it is on the SAFC II. If you look at the other end of your harness (if it hasn't been cut off). The order the wires are in might be the same going into SAFC itself. Dose that make sense?

 

[darkiller_666]

Yeah that makes too much sense for me to nto of thought of before. Luckily i had the wire wrapped around a bar behind the dash so my wires didnt get ripped from the ecu, but i also forgot it had signal wire harness. I think only common sense says that they should be in the same order. Thanx again