Pics of my Head ported by FullyBuilt Motorsports

[FullyBuiltDSM]

I just got my head ported and here are the results what do you guys think???
http://www.srtforums.com/forums/showthread.php?t=181931&highlight=dsm <<here are the pics.

 

[gamingguru]

Don't really want to register on the SRT-4 forums just to look at the pics, Could you post them up on here?

 

[Julia]

Don't really want to register on the SRT-4 forums just to look at the pics, Could you post them up on here?

besides..the first post sounds like a sales pitch.....careful.
Julia

 

[FullyBuiltDSM]

sry guys here are the pics.

 

[FullyBuiltDSM]

bigger pic

 

[FullyBuiltDSM]

what do you guys think???

 

[Julia]

Looks really nice
Julia

 

[gamingguru]

looks allright to me. I wish that I had some picks of my head before I put it on to compare to. You didn't polish the ports did you?

 

[FullyBuiltDSM]

i didnt do the work it was done at FullyBuilt Motorsports. As far as i know they are going to polish them. Its not done yet there doing some more valve work.

 

[sYnOnYx]

clean, my boy matt and his 12sec neon are sponsored by fully built.

 

[woooop]

are your valve guides cut smaller

 

[alexsmede]

look like to me they did a really nice job.

what do you plan to do to your car, like what other mods do you want to achieve

what are your goals?

 

[FullyBuiltDSM]

yea the guides are smaller, so far ive got a full rebuild, wiseco pistons, eagle rods, toga bearings, forged crank, complete gasket set, just got a 50trim ill be sending to fullybuilt to have ported, that head of course, ferrea dual springs. front mount, hopefully some comp 200's within a week or so, safc2, 750cc injectors(in the mail), walbro 255, that sbr cast manifold, 3 inch turbo back.... im sure i forgot somthing but thats the stuff ive got so far. Ill be off the road till spring but i figure its well worth the wait .

 

[gridlyne]

Pretty. Thats an A+ job. I have seen ports done much, much worse. But thats great!

 

[Fusa]

Is that a 1g head ?

 

[~laser_craver~]

well lets see he drives a 93 gst, and if i remeber correctly thats a 1g

 

[napkinthief]

Thats some beautiful craftsmanship, and its shiny as hell and not polished yet, can't wait to see the end result...mind me asking how much you paid? and approx. HP increase?

 

[webshell]

you might wanna use something other than an SAFC to tune that bad boy.

 

[yunior]

that looks really nice

 

[FullyBuiltDSM]

Thats some beautiful craftsmanship, and its shiny as hell and not polished yet, can't wait to see the end result...mind me asking how much you paid? and approx. HP increase?[/QUOTE

Those were some of the pics, but like i said they were still going to polish it do a valve job and a few other things. As far as the price goes im not posotive because im asking him to do more and more things daily. He guarantee's that he can beat any competitors price though. Ill ask him to tell me what i owe for what he's done and then ill post it later.

 

[FullyBuiltDSM]

Is that a 1g head ?

Its actually a first gen N/A head........ shhhhhh its got different guts though

 

[FullyBuiltDSM]

you might wanna use something other than an SAFC to tune that bad boy.

yea i have an safc2, wideband and all that mumbo jumbo... i hate wiring

 

[FullyBuiltDSM]

Thats some beautiful craftsmanship, and its shiny as hell and not polished yet, can't wait to see the end result...mind me asking how much you paid? and approx. HP increase?

josh from fullybuilt motorsports say that if you send your head an entire port and polish job including a valve job comes to $650 and he will sandblast it too

 

[~laser_craver~]

how bout LINK FOR THERE WEB SITE

 

[FullyBuiltDSM]

his site has been down for a while if you need anything get ahold of me with a private message and ill hook you up with a phone number