The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

20250709_143406.jpg

Black Cherry

Spends most of its life on jack stands

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Finally started working on the car again, it's been slow making any progress, but it's getting so close.

Engine installed
1000016850.jpg
-4an lines for the wastegate/ boost controller
1000016752.jpg
making up hoses for fuel, catch can, etc.
1000016853.jpg
Test fitting the intake and wiring up a dual fan relay, got the passenger side fan mounted. Just waiting on some deutsch pins and a 10" pusher for the driver's side to come in.
1000016859.jpg


20260722_025727.jpg


20260722_025806.jpg
 
First time off jack stands in 9 years!
1000016981.jpg

1000016980.jpg

I'm moving the car to my shop tomorrow to get it on the lift to complete the next phase of the build. Going to clean and restore the undercarriage and install all new parts including a natfab tubular subframe.

Here's part of the fleet already at the shop
1000016983.jpg
 
Things are getting pretty serious over here. Dropped the gas tank
20260821_011731.jpg

Rear diff, subframe etc. all coming out
20260821_011741.jpg

So much room for activities
20260821_023545.jpg

Out with the old
20260821_023554.jpg

Next up the plan is to clean the undercarriage, paint it, and then undercoat it. Getting everything prepped for the natfab tubular rear subframe & trailing arms to go in. Basically everything will be new or freshened up.
 
Took a little while to get some things done but I'm back in the shop making it happen. I had the undercarriage dry ice blasted and it cleaned up pretty good.

install of the rear subframe in progress
20261105_224753.jpg

Trailing arms, swaybar, and control arms bolted up.
20261107_043459.jpg


20261107_223028.jpg


20261107_225911.jpg

Going with all new wheel bearings and restoring the axle stubs and cups. I should have just cut the tone rings and old bearings off, they were on good and came off hard with a 3 jaw.
20261106_210921.jpg

Blasted and painted and installed new dust shield
20261107_222809.jpg
20261107_223322.jpg
20261107_231136.jpg

Brake dust shields painted and wheel bearings pressed in.
20261107_225535.jpg

That's a wrap for the night. Next up, brakes, rear diff, dss drive shaft and axles, jxb carrier install, and gotta decide what tires to go with the evo 8 wheels.
20261107_230311.jpg


20261107_225925.jpg
 
I gotta know how much was t he dry ice blasting. Ive wanted to do this for years.
It was a mobile guy that charges 150 an hour, took about 8 hours. Not exactly cheap, but the results were worth it in my opinion. I'm in the Seattle, Washington area, so prices are probably higher than other parts of the country, as well.
 
More progress, just doing what I can here and there. Started out by putting the FF billet rear diff cover on a fresh TRE built 4 bolt.
20261109_033617.jpg


20261109_033622.jpg


Then threw it in the natfab tubular rear subframe. This actually took a ton of massaging and adjusting and using an Allen head bolt on one of the top mounting holes to get it to line up. For being "jig built" I honestly though it would fit better but alas, it's in. The sway bar rubs on the subframe also, but I ordered up some energy suspension bushings to see if they will space it up a hair more than oem. If not, natfab said he would send some spacers, he was really responsive and helpful so I can't knock him too hard for the fitment issues.

Capped off the rear end with DSS 1000hp axles, these things are beefy!
20261110_163458.jpg

20261119_183948.jpg

Moved on to getting the rear brakes installed. Went with ebc rotors and yellow stuff pads. Painted the rebuilt calipers and brackets black, came out real decent.
20261110_173321.jpg
20261119_201633.jpg


Finished the night off with the JXB carrier and DSS 950hp aluminum driveshaft w/ sonax yoke, ran through a boosted fab driveshaft loop to a magnus billet 300m t-case.
20261119_183959.jpg

You can see some dark spots in the factory undercoating, it's like a wax or grease or something that is a nightmare to remove. The dry ice blaster ran out of ice because it took so long to get it off, but he's going to come back out and finish the job for me.
20261119_190321.jpg


20261119_190321.jpg
 
Last edited:
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Build Thread Updates

Latest Classifieds

Back
Top