The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

Post a Question

standalone

  1. Evannewell19

    420A MegaSquirt ECU for 420A

    What all do I need or should I get if I want to MegaSquirt standalone for the 420a?
  2. Gonza97

    1G Tachometer not working on standalone ECU + different ignition module

    Greetings group. I´ve installed a standalone ecu, and my tachometer is refusing to work (It did work previously before the change). I also must say that I've replaced the ignition control module to another brand, so it's been a pain to know how to adapt it either to the module or to the...
  3. midfb6

    420A In need of some guidance

    I recently got my car back from the welder and have all my intercool piping done. I'm ready to start installing the MS3 to the car so i have 2 questions. 1. Would it be better to piggy back the ecu till motor is broken in, Ik fully standalone is alot more work. 2.Would someone be some help on...

  4. How to wire in the MPI relay to use it for a standalone ECU (maxxecu)

    Hello fellow techs,Since i am switching to maxxecu I am wondering how to wire in the mpi relay so i can use it for the maxxec.I am stuck at the mpi side. pin 8 (mpi) goes to 63 and 66 of the ecu (switched to ground) if pin 3(mpi) gets power from the ignition sw.Now, do I connect pin 8 of...
  5. jlust07

    General Speedunio No RPM Signal

    Hello all!About 2 months ago I ripped apart an old 1G ECU to use as an adapter harness for a Speeduino V3 DIY board, after assembling the board I went to crank over the engine and didn't see any RPM output in tunner studio. I made sure to jump the J5-6 pins to allow for hall effect sensors...
  6. AEM EMS 30-1310 2g DSM
    Sold

    For sale AEM EMS 30-1310 2g DSM

    Fully functioning AEM EMS 30-1310 for 2g DSM.
    $450.00
  7. Harrison Scholten

    General Speeduino standalone

    I was wondering if anyone has any info about the speeduino/arduino standalone ECU and tuner studio software. Specifically how user friendly the software is, how hands on the ECU installation is.Does the board require assembly or come with a harness that can be soldered to the factory wiring...

  8. 2G Vi-pec Standalone

    Hi everyone,I was wondering if anyone here is familiar with a Vi-pec standalone? I had one installed in my car and I was told I can use it to help diagnose the issue I've been having. I didn't receive a book for it and have had troubles finding much info about it online. I've been trying to...
  9. Spdfreak

    For Sale 1995-1999 GSX/GST Aem Ems V1 1310 plug and play $600 obo

    Aem standalone 1995-1999 Mitsubishi Eclipse gsx/gst plug and play ecu includes serial to USB data cable $650 shipped You must be registered to see element. You must be registered to see element. You must be registered to see element.
  10. Chaas250

    For Sale Proefi 48 stand alone with flex fuel

    i have a full standalone system proefi48 with all the parts and accessories Looking to get rid of it. it is all still brand new in never opened packages I’ve decided to go a difrent route. Looking to sell it all at once. have plug and play harness for 1g. $2400
Boosted Fabrication
ECM Tuning
ExtremePSI
FIBA Motorsport
Fuel Injector Clinic
Innovation Products
Jacks Transmissions
JNZ Tuning
Kiggly Racing
Morrison Fabrications
Rix Racing
RockAuto
STM Tuned
Support Vendors who Support the DSM Community
Back
Top