The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

20261004_141746_preview.jpeg

1992 Eagle Talon TSI AWD

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

I have both so I can play with it, gonna swap it out if I can figure out how to make it talk to ecmlink.
If the electrical plug is the same, all you need to do is change the "MAP sensor type" on the ECU Inputs page to "GM 3bar" like this:
MAP sensor type.png

Probably should post a link to the Amazon page that you bought the 3-bar sensor from, just in case it is something different from the regular GM type. The regular GM types all have the same volts to pressure scaling, so the idea would be to make sure your 3-bar is a regular GM type.

Well man, no ISC at all, I'm surprised it started as well as it did from 54 degrees F.
As far as the idle switch then, just keep using the simulated switch like I showed in the pic in post #49.


I have noticed when I press the throttle it doesn't really register in ecmlink until it is pressed in a bit.
This makes it sound like there *is* some slack in the throttle cable, or somewhere. What kind of TPS do you have on it?

Noted some good things:
You have a real narrow band O2 sensor. Yay. That's going to be better than simulating from a wideband.
Your battery voltage was nice and high during cranking.
Your CrankingFuelAdjust is working (that's a logable item).

For connecting the wideband to the ecu, usually on a 1g you run the analog signal wire from the wideband to the EGRtemp input on the ecu.

I'm glad your wideband is an Innovate MTX-L. I figure anybody using an Innovate MTX-L is kind of doing a service for the DSM community, because ECMtuning is still recommending the much older LC-2 without any mention yay or nay about the MTX-L. So the more user experience we can get on the 1g DSM with MTX-L the better. We kind of know that the AEM widebands often have trouble with our inputs. The older Innovates seem ok, but there are fewer of the newer MTX-L's out there so it's harder to say about them.
 
Oh boy do I have some updates and news!

1) I caught that Omni Power 4-bar MAP sensor red handed! When it gets warm, it craps out! Check this out


The Amazon 3-bar MAP is in now and it seems to work great! This is what I got: https://www.amazon.ca/dp/B09NVP4DFB. It was plug and play like you said. The pigtail it came with was junk but I just used what I already had in the car.

The "3 Bar Omni Power" pin option in ECMLink seems to be giving me most accurate results I think. I hooked up my air compressor to it and validated it and it was accurate at like 0PSI, 10PSI, 20PSI. So far so good - no more random smoking and stalling. I wiggled all the cables and connectors as much as I could and didn't see anything weird on the datalog so I'm hopeful

And second... I'm a goddamn idiot. We mistimed the engine. :ohdamn:.

That lopey, rough, shaky idling? I was off by a tooth on both intake and cam gears.

We were so focused in getting the tension right that I guess we screwed up the belt. Or maybe we just didn't really understand the timing marks. I dunno how we got this wrong.
1792264647117.png


My god, how close did I just come to wrecking the engine? I put a scope into the cylinders and they look perfectly fine to me... hopefully I got away with it? :shhh: I'd like to check compression but I don't have a compression tester of my own yet.

So, uh... I just used the adjustable cam gears to retard the intake and advance the exhaust cam by 7.5 degrees to compensate for the mistake because like, there's no way I'm taking the engine out again this year. That feels dirty, but holy crap the engine sounds like a normal engine now when it's idling not like a cammed out V8 corvette.

1792264716946.png



Now, for the first time I'm finally able to set the base ignition timing right! It wouldn't go any closer than 10deg BTDC before even with it cranked all the way over.

Before:



And After:

 
Last edited:
I caught that Omni Power 4-bar MAP sensor red handed! When it gets warm, it craps out! Check this out
Wow, well there you have it! I'd say that is nailed down. Very satisfying. The Omnis have been getting a bad rep for a while now but this is the best wrap-up I've seen for it. ECMtuning quit selling them about a year ago with no explanation that I know of. Their links that used to take you to a page where you could buy one now give you "Product not found" LOL
I wish we could know if the GM style Ballenger MAP sensors are different internally and reliable long-term like these sensors used to be (as far as I know) previous to about 10 years ago. There are 2 guys in here that have switched to them but don't have a lot of miles on them. So not enough user history to say yay or nay. Anyway here's links to them. Read the Description field for the 3-bar. It's interesting. They say that even the Delphi (Genuine) ones are bad now. They show good charts and diagrams. One diagram shows that the inlet pipe should be pointing generally downward and they give the maximum angle from straight down that is considered OK as 30 degrees. Presumably that is so that any condensation of water that gets in the hose will not lay around in the sensor, it will fall out back into the hose.
Ballenger 3-Bar GM MAP
Ballenger 4-Bar GM MAP

For my own car I switched to a 3.5 bar AEM stainless MAP sensor a few years ago, but the Omni 4-Bar that had been on it since 2016 was actually still ok as far as I know, and it is sitting right here on my computer desk holding down a stack of loose papers!

Well now you are a top expert on evaluating MAP sensors, so you are in good shape for catching it if your brand new KEJSTED (?) sensor gets weird!
 
I just used the adjustable cam gears to retard the intake and advance the exhaust cam by 7.5 degrees to compensate for the mistake
7.5 degrees sounds ok to me. That would be one tooth if the wheels have 48 teeth which is about what they have.
I don't think there would be any damage from it being one tooth off for a while.


Yup, awesome. Sounds just like my stock 1990 Toyota Corolla. It doesn't get any better than that.
The MTX-L gauge looks good running. Where do you have the wideband sensor mounted to the exhaust?
 
It's on the downpipe, I want to say like ~8 inches after the flex pipe
That should be ok as long as there aren't any leaks in the flex section.
Usually, I'd say it's better to have it before the flex section, like this:

20221020_wideband sensor in the Talon.jpg

But Innovate always seems to like a location that is pretty far away from the turbo outlet. Like they say "at least 24 inches" in your user manual. So I guess I'd leave it where you have it if it seems to be working right at light loads. That's when the far-away location would be at its weakest. And you can tell if it's working right at light loads because your real narrow-band will be giving you real stoic when you are in closed loop. It's awesome having a real narrow-band.
 
Hey so, I don't know if I'm being paranoid or not but I noticed there's a mark developing on my timing belt after about 25km of driving it

1792371028028.png

1792371038111.png


There was a faint bit of residue on the belt, like oil maybe? I'm not sure... I gave the belt a wipe down and it seemed to come off clean but... any idea what's causing this? Or do I need to be worried? I'm questioning the rest of my timing job now that I found out I mistimed the darn cam gears LOL

1792371090783.png



There's a faint intermittent ticking, it's faint but I can catch it with my phone sometimes but I can't tell where it's coming from if that's the timing belt rubbing on something or what

 
There was a faint bit of residue on the belt, like oil maybe? I'm not sure... I gave the belt a wipe down and it seemed to come off clean but... any idea what's causing this?
Do you have new tensioner and idler wheels in there?
We did see a case here in 2018 where somebody had a fairly new Gates idler wheel and it was leaking out a little bit of grease. He didn't say anything about it leaving a mark on the outside surface of the timing belt. But he was concerned about it leaking.
If it is one of those wheels leaking, it could be that it has bad seals, or it could just be that when it was made it was filled to like 80 or 90 percent with grease, which is not supposed to be the way to do it. There's a rule of thumb for it, I think it's around 30% filled. (SKF, NTN, etc)

I see the actual Mitsu OEM Koyo idler wheel and NTN tensioner wheel are still available from STM. Pretty expensive.

You could be leaking oil at the bottom end of your dipstick tube, where it goes into the block and has an o-ring. That's a common leak area. Hopefully that shouldn't get inside of your belt cover though. And of course there are other, worse things under the timing cover that could be leaking oil.
 
I think you might be right about the Gates idler wheel. The more I drive the car the more that residue seems to have disappeared. I did discover that my oil pan bolts under the timing belt were too long... they were 12mm long, the ones under the timing belt are supposed to be 8mm. Idk why these are the bolts I got with my original car... but in any case I think that was making that mark on the belt and it's fixed now... with a few washers. At least I hope.

It's almost the end of the year, I don't think I can do too much more on the car before I have to put it away. But... not having idle air control has been driving me absolutely nuts so I got my FIAV + ISC off the doner car and got it installed :D

Had to relocate the battery to the trunk though:
1794371719540.png

Got this plastic "boot jack" thing from Princess Auto, cut it down to size and it's bolted to the firewall and provides an insulated post that the positive battery terminals can connect to that is far enough away from everything.

1794371764819.png

And... battery moved to the trunk! That was where my subwoofer was going to go... but oh well.

I thought you might get a kick out of this. So... the ECU still doesn't seem to actually drive the ISC motor right now. It doesn't do anything when I turn the key on. So I'm not sure what's up with that I thought the pintle is supposed to move in and out when you turn the car on but it doesn't do anything at all. So I made a little Arduino stepper motor controller to drive it just to test and make sure the thing works:



It works! So I installed the ISC into the car, used the Arduino to set it's position to be fully extended so it closes off the air. Car idles at around ~1500RPM now and the FIAV works now to keep the RPM higher while it's cold. Still seems to be idling kind of high though...

I don't know maybe I'm going down a rabbit hole I shouldn't be right now because I guess I need to figure out why the ECU doesn't seem to want to control the ISC, and also why my idle is so high. But I feel like it's a step in the right direction, it is so nice to have the battery out of the way and not in the engine bay anymore.
 
Last edited:
I thought you might get a kick out of this

Yes, looks like you have a manual operation ISC there. Awesome! Except that you won't be able to read the ISC Position in a log I guess.
One reason for the ecu not operating the ISC is that the driver chips in the ECU could be blown.
There are 2 chips that run the ISC.
This wiki page has a rundown on the driver chips, and a picture of blown driver chips - some very visible ones. I suppose it's not always this visible.
The page also lists the driver chips by IC number and what each one does.

The high idle - I don't know, does the FIAV seem to be working kind of normal? I guess that would be, if your ISC is closed, and the engine is warm, and your warm idle is about the same rpm as it was when you had the blockoff plate on it, then the FIAV is probably closing all the way when it is warm, which is what you want. Then the air leaking in must be coming from something other than the FIAV.
 
Last edited:
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Build Thread Updates

Latest Classifieds

Back
Top