Mike Rizzotti - 9's Stock Block 1G

[tsi1991awd]

First thing I noticed was he jumped it and got the red light. But not a bad pass.

 

[4WARND]

I did not realize there was a thread here already. I started my own.

http://www.dsmtuners.com/forums/drag-strip/383090-9s-finally-stock-shortblock-internals.html

Was the car ever disassembled and reassembled and used stock parts or is it a motor with however many miles straight from the factory?

No, only time the oil pan has ever been off was about 10 years ago to pull the balance shafts. The pistons, rods, bearings, rings, ect. are the originals from the factory with 98k miles and hundreds of drag runs. I have owned the car for 17+ years and been racing for 15.

Here is a video I made:

Mike Rizzotti Talon 9 second pass! - Car Videos on StreetFire

 

[907dsm]

Congrats man.. that's freaking amazing. Wait your revving your stock motor to 10k??

 

[4WARND]

Congrats man.. that's freaking amazing. Wait your revving your stock motor to 10k??

No. The rev limit is set there. I typically shift the 1-2 around 9400 and the rest around 9000.

 

[Ghostcrafter]

I need to show this to a few people here who went on a rant telling me that I shouldn't use stock internals if I wanted to hit 450+bhp.

Quite interesting...

Oh, and congrats, .

 

[EclipticalGS]

and people think its funny I run 450 on 1g rods and NPR 2g pistons...Makes me want to gut and cage my car. Thanks

 

[Ghostcrafter]

and people think its funny I run 450 on 1g rods and NPR 2g pistons...Makes me want to gut and cage my car. Thanks

Same setup I'm ordering in the next few months for my rebuild. DSMGY Frankenstein 1g Rods with NPR 2g Pistons. Aiming for about 450 on this initial build.

Might have to put in a cage while I'm at it as well. Already gutting part of it to put in carbon fiber.

 

[Boostjunki84]

Congrats Mike!

 

[GRNDSM]

I did not realize there was a thread here already. I started my own.

http://www.dsmtuners.com/forums/drag-strip/383090-9s-finally-stock-shortblock-internals.html




No, only time the oil pan has ever been off was about 10 years ago to pull the balance shafts. The pistons, rods, bearings, rings, ect. are the originals from the factory with 98k miles and hundreds of drag runs. I have owned the car for 17+ years and been racing for 15.

Here is a video I made:

Mike Rizzotti Talon 9 second pass! - Car Videos on StreetFire

Wasn't I helping you with that job, back then? As I recall, Fish actually pulled and reinstalled your BS bearings.

Congrats Mike!!!

 

[4WARND]

Wasn't I helping you with that job, back then? As I recall, Fish actually pulled and reinstalled your BS bearings.

Congrats Mike!!!

Leon, yes you were. You are correct, the BS bearings were new about 10 years ago. I was referring to the rod bearings, which are the originals.

 

[white92talontsi]

Man this is friggin nuts. Who does your tuning? Whoever it is is doing 1 hell of a job.

Sent from my SPH-D700 using Tapatalk

 

[4WARND]

Man this is friggin nuts. Who does your tuning? Whoever it is is doing 1 hell of a job.

Sent from my SPH-D700 using Tapatalk

Thanks. I tune the car.

 

[white92talontsi]

Thanks. I tune the car.

Awesome.

Sent from my SPH-D700 using Tapatalk