What lb/min are you flowing on pump & bigger turbos

[fulanititoo8198]

Just want to see what you guys are running as far as lbs/min or cfm with big turbos and your daily driven setups. Pump gas ofcourse.


I have my scm 6152e at 15lbs seeing 30 lbs/min no tuning at all since I don't have much to tune it with yet. Needing a wideband . I think it would be cool to see the differences between all the different turbo's people are using now a days with your daily drivers.

Thanks for the space!

Edit: I have it up to 32 at 15lbs

Edit: Been tuning it's at 36 at 15lbs but this is with an uncalibrated maft but at least it's improving.

 

[donmagicjuan]

- EvoIII 16G
- 26 psi on 92 octane + water/meth injection
- ~39 lb/min

 

[biglady112]

19lb/min at wastegate pressure on my galant(14b).

35lb/min @ 21psi Evo III 16G on a stock 96 gsx(stock head, motor, cams)

44-46lb/min @ 20psi on a built 95 gsx SCM6152(stroker, stock cams)

44-46lb/min @ 20psi on a built 91 gsx SCM6152(stroker, 272's)

47lb/min @ 22psi SCM6176 1989 Mitsubishi Mirage(bone stock 2.0L top to bottom)

Dsmlink powers all cars above. All cars above are at 5800ft above sea level


Steven

 

[fulanititoo8198]

- EvoIII 16G
- 26 psi on 92 octane + water/meth injection
- ~39 lb/min

and you drive on 26lbs daily?

 

[nanokpsi]

PT67 (.68 t4/p trim)
stock 2g motor/head/tb with hks 264/272 cams + 2g magnus
47lb/min 23 psi 70-80* intake temps
Stock 2g mas

 

[2gGSX]

- EvoIII 16G
- 26 psi on 92 octane + water/meth injection
- ~39 lb/min

Out of curiosity, is this about the same airflow number you had when you made your dyno numbers? (354 whp)

 

[RedTurboEclipse]

40lb/min pte scm 50, stock motor/cams, 20psi dsmlink

 

[CanadianTSi]

43lbs/min. 50 trim, FP2x's, Magnus, 24psi, 94oct.

 

[MyBeatGSX]

I feel low and left out... and I know he said "big turbos" but someone else listed their Evo.

33lb/min Evo 16g 20psi, stock motor/cams, 93 octane

 

[Turbo Monk3y]

47lbs a minute 23psi

54-55lbs a minute 28-29psi Stock unmolested maf stock 6bolt bottom

 

[Coup D E'Tat]

49lbs/min at 24PSI
51lbs/min at ~26psi

Stock 2G MAS, stock 6-bolt, SMIM, and cams. 93 octane, with 18* peak timing.

SC61 - .63 T3

 

[shleppy]

53-55lbs at 28 psi with 93 and water/meth injection depending on the air temp. Ported 1g with cams and smim, calibrated maft and dsmlink.

 

[90blacktsiawd]

39-40 lbs/min - 21psi scm5031bb stock head/intake manifold/comp 200's/93/meth injection logged through dsmlink/ 3bar gm map sensor.

I have seen up to 44 lbs at the same boost depending on the weather though.

 

[fulanititoo8198]

I was expecting to see people running 15-17lbs of boost on their daily setups. I'm impressed, some nice flow you guys got going

 

[zippyshoe]

27 lb/min at 15psi on FP Big28 (OK, maybe not that big) and 93 octane.

 

[TSIMonsteR]

- EvoIII 16G
- 26 psi on 92 octane + water/meth injection
- ~39 lb/min

just so you know, I am modeling my setup after yours.

 

[90blacktsiawd]

I was expecting to see people running 15-17lbs of boost on their daily setups. I'm impressed, some nice flow you guys got going

Where's the fun in that?

 

[DSM90AWD]

Fiddy trim 45.5 lbs/min @ 21.5psi (mods in profile)

 

[donmagicjuan]

and you drive on 26lbs daily?

Out of curiosity, is this about the same airflow number you had when you made your dyno numbers? (354 whp)

Yes, and yes.

 

[RavenX]

45lbs/min@24psi with pump/meth on a PTE DBB 57trim with a custom TO4E anti surge ported compressor cover. Mods are in profile.

 

[donmagicjuan]

just so you know, I am modeling my setup after yours.

Very cool, I hope you have as much luck with it as I've had!

 

[spyderturbo007]

EVO III @ 20psi, stock cat back, stock SMIC is good for about 31 - 33lbs/min on my setup depending on the ambient temp.

EDIT ---> I must say, that some of you guys are flowing some serious air

 

[oldman]

36 lb/min @16psi on GT12.

 

[Mike1992]

36lb/min at 19 psi Small 16g

 

[Black95TSIawd]

32lbs/min at 18psi on my b16g.