Hey guys I got a 99 gsx I want to replace the factory BOV. I bought a 1g bov but want to make sure I have everything I need to make the install. So far this is what I’ve ordered. Do I need to get anything else to make the install?
Hi,
When boost leak testing should my bov be opening up?I have a NGR type sEverytime I try to pressurize my system it's basically releasing the air and the only way I can test it is when I cap it off, but even then it's hard to seal the hole off.When driving it works like normal and I can...
Hey guys I just swapped out my upper inner cooler plastic pipe with a hard metal pipe. I have the 1 G BOV and I also have a engine hard intake pipe that I’m trying to figure out which type of hose I can mount that will be as little restricted as possible! See pic!
$450 2G Hahn SMIC Intercooler; Super rare part good for 400hp maintains stock look and is direct bolt on for 2Gs
$100 Nissan GTR R32 BOV / 1G BOV; Same part number as 1G BOV but is gold and has Nissan stampings
$20 Boost leak detector for stock T25 turbo inlet size
$100 Genuine Injen Intake with...
INTERCOOLER NOT INCLUDED. This piping kit is now out of production by Punishment Racing, so this kit is truly rare! It has never left its box and has been kept in a safe and dry location. Comes with all of the piping, silicone hose and clamps you will need to install your own intercooler on your...
What's up guys I'm new to this form so bare with me. I bought a 99 gst Spyder convertible stock bov stock set up. Well I bought a eBay blow off vavle and had to get bigger pipping to make it fit. I got in it today and noticed that my boost Gage was a quarter spooled under no load. The car ran...
My car was recently wrecked so my loss is your gain everything was working properly when I got involved in the accident you can make me an offer the worst I can say is NoEprom Ecu socketed currently has a chip that was burned for my setup but you can remove it to use Dsm link SOLDVRSF 2g...
I have a 1g dejon tool smic kit for sale. Not all pieces are dejon tool as it wasn't complete when I purchased it.It has the DT TB elbow, upper pipe w/bov flange and modified intercooler.The lower pipe and j pipe were put together to complete the piping, and couplers are STM 4ply.Also...
So I'm learning about cars on my '91 Galant VR4 with a '95 Eagle Talon TSi turbo swap and I don't know a lot about how an engine bay should look, especially a turbo one. The first pic is on the pipe that goes from the intake manifold to the intercooler. My friend who works on mostly diesel...
I've been feeling like my 14b 2g was lacking in the power department. So I started looking around for problems and I found that my hks bov was spinning freely on the flange. I took the o ring out and installed it with the snap ring only. It's super tight on there now and tested it for a boost...
Hey every one long time lurker here finally decided to sign up and make a first post. I live in Colorado and bought my 1g Talon over a year ago and have had tons of problems ever since! Failed emissions an embarrassing number of times. Which is my fault for thinking small fixes and tinkerings...
I've been looking for the answer for hours but haven't been able to find anything on this.
So I am running speed density and have already payed someone to tune the "turtle" with my BOV recirc'd to the IM.
My question is, if I just vent the BOV to atmosphere now, will it mess with my tune?
I...
I have a few extra parts kicking around I don't need anymore.
-T25 from my 5 speed 2g tsi awd. In working condition was run at 12psi, but I recommend a rebuild but should run a while.
-T25 from my 2g auto gst, does have a bit of shaft play but didn't burn oil, doesn't hit compressor walls...
So this is my question. I have search for 3 hours or so on Google, on here, and on other forums as well like MazdaSpeed and im still unsure of what im looking for. So far i have read that BOV release the pressure into the air and that bypass valves send the pressure back into the intake system...