Welcome to DSMtuners - The Talon, Laser, and Eclipse performance enthusiast resource

















Login



See All DSMtuners Supporting Vendors
Go Back   DSMtuners > DSM Forums > General > Newbie Forum

Newbie Forum Beginner/newbie/general DSM questions. first mods, how to run 10's when you haven't run 12's yet, any tech question that doesn't fit in another tech forum. New Members must limit their tech posts to this forum and sub-forums.

Reply
 
 
LinkBack Thread Tools
Old 11-24-2006, 12:30 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #1 (permalink)
Proven Member
 
From: amenia, New York
Registered: Jul 2006
Tech Posts: 78
Classifieds Rating: 0
Reputation: Joeyxx07 is an unknown
Question oil leak inside turbo into intake piping

ok so i pulled off the snorkel on my 2g talon and found what i think to be oil in there. now i know my car is leaking oil is this where its coming from? if so what could be causing a leak like that. i have picutres but its pretty self explanatory. I also think i have a small 16g becasue the fin sizes are different and theyre dual fins. Any help would be greatttttly appreciated!

_-joey

Reply With Quote
Advertisement



To browse the forums without the advertisements above, Login/Register
Old 11-24-2006, 12:39 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #2 (permalink)
Proven Member
 
From: Flushing, New York
Registered: Sep 2003
Tech Posts: 543
Photos: 5
Classifieds Rating: 6
Reputation: hewhoisknot is more helpful than not
Do you still have all the stock emissions lines hooked up to you're intake? If so it's probably just blow by, if not it could be turbo seals, although the oil is usually found on the side going to the IC though.

BUN
View photos of this member's car 

Reply With Quote
Old 11-24-2006, 12:41 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #3 (permalink)
Proven Member
 
From: amenia, New York
Registered: Jul 2006
Tech Posts: 78
Classifieds Rating: 0
Reputation: Joeyxx07 is an unknown
yeah, they are all still hooked up, whats blow by?

Reply With Quote
Old 11-24-2006, 12:45 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #4 (permalink)
Proven Member
 
95blackGsTurbo's Avatar
From: Peoria, Arizona
Registered: Aug 2003
Tech Posts: 2,870
Photos: 12
Classifieds Rating: 1
Reputation: 95blackGsTurbo is an experienced, knowledgeable member worth listening to95blackGsTurbo is an experienced, knowledgeable member worth listening to95blackGsTurbo is an experienced, knowledgeable member worth listening to95blackGsTurbo is an experienced, knowledgeable member worth listening to
Check the shaft play of your turbo. See if you can move the compressor wheel, up/down, side/side, in/out. Also check the line that goes from your valve over to your intake to see if there is oil buildup inside of it. Blowby is when your pistons rings start to wear down and crankcase oil is making it into the combusion chamber. It will usually cause the car to smoke.


____________________________
Adam Thilges
View photos of this member's car 

Reply With Quote
Old 11-24-2006, 02:18 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #5 (permalink)
Proven Member
 
From: amenia, New York
Registered: Jul 2006
Tech Posts: 78
Classifieds Rating: 0
Reputation: Joeyxx07 is an unknown
well i checked my shaft play and theres is verrrry little side to side, no in and out. Can i pop off thos lines without having clips? how should i reattach them then

Reply With Quote
Old 11-24-2006, 09:56 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #6 (permalink)
Proven Member
 
From: Flushing, New York
Registered: Sep 2003
Tech Posts: 543
Photos: 5
Classifieds Rating: 6
Reputation: hewhoisknot is more helpful than not
Yes you can pop the lines off, just put a little filter on the line, or use a catch can.

BUN
View photos of this member's car 

Reply With Quote
Old 11-24-2006, 10:22 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #7 (permalink)
Moderator
 

oldman's Avatar
From: Dayton, New Jersey
Registered: Jun 2003
Tech Posts: 9,248
Classifieds Rating: 26
Reputation: You can trust this leader of the site
Quote:
Originally Posted by 95blackGsTurbo
Blowby is when your pistons rings start to wear down and crankcase oil is making it into the combusion chamber. It will usually cause the car to smoke.
Not exactly, more like the opposite. Blow by is air/fuel mixture leaking into the crankcase on the piston's compression stroke.


____________________________
Bruce

Reply With Quote
Reply


Bookmarks

Thread Tools

 

» 2010 DSM Calendars
» DSM Mechanics Gloves
» Recent Blog Entries
Update 4
by: Kevin TSI

Engine shots
by: Spdfreak

Best DEAL ever *Update*
by: 4Motion4g63

2.4 Liter G4CS build thread
by: Atuca

Possibly buying a new 1G
by: booostedGSX
» Recent Tech Threads
Title, Username, & Date
My new triple fuel rail setup
by: biglady112
EVO III motor
by: boostingsx98
Where can I find original Eagle blank keys?
by: One Equals Two
First time back at the track...
by: Gooberlog
420a exhaust question?
by: gudz519
» Latest Gallery Photo
User quakeroats11
» Advertisement
» Current Poll
What will you be buying soon?
DSM Calendar - 36.84%
7 Votes
15 Votes
5 Votes
Total Votes: 19
You may not vote on this poll.
Powered by vBadvanced CMPS CMPS v3.2.1

All times are GMT -7. The time now is 08:54 AM.

DSM Forums | Pontiac Solstice/Saturn Sky Forums

© 2009 SPEEDtuners Network, LLC All Rights Reserved

Search Engine Optimization by vBSEO 3.3.1