Welcome to DSMtuners - the largest Mitsubishi Eclipse, Eagle Talon, 4G63t and 420A DSM performance resource on the web



















Login



Go Back   DSMtuners > DSM Forums > General > Newbie Forum
Welcome to DSMtuners - the largest Mitsubishi Eclipse, Eagle Talon, 4G63t and 420A DSM performance resource
You are browsing the site as a GUEST. Please login (or register) and gain the ability to post on our site and interact with other DSMers. You also get to browse the site with fewer advertisements. It is FREE to join!

Newbie Forum: Beginner/newbie/general DSM modification questions. First mods, how to run 10's when you haven't run 12's yet, any tech question that doesn't fit in another tech forum. Probationary Members must limit their tech posts to this forum and sub-forums.

Reply
 
 
LinkBack   Thread Tools
Old 06-13-2009, 06:06 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #1 (permalink)
Probationary Member
 

A80Avant's Avatar
Registered: May 2009
Tech Posts: 17
Reputation: A80Avant is an unknown

Holset HX super 40 compressor map


Hi

im new here, and im going to be using a holset HX40 on a different car, its a 5cyl 2.2 audi engine.

I have already ordered the T3 0.70AR hotside to go along,and the turbo is going to be a 7blade super 40.

Now unfortunatelly,most of the cmp.maps i see online to compare come in lbs/min and the ones i have found on several forums reguarding the holset turbos come in maf flow or kg/sec.

I have doubts when i see this map: as at the bottom it says kg/sec but on top it shows lb/min.BUT shouldnt the lb/min be much higher than the kg/sec that is at the bottom of the graph?

essentially i cannot understand what is the max flow of this turbo from the map, although i read lots of reports on the mitsu engines and it's potential.

Reason i ask to clarify if there is a different map that i can look at,is the fact that for the beggining i want to go easy on the turbo as im not going to be replacing my clutch disc,and this one can hold up to around 600Nm torgue (crank),so i know that the HX40 can produce much more on the 5cyl engine,therefore i will have to tune for the lowest safe boost at start.
Attached Thumbnails
Click image for larger version

Name:	Hx40---7blades-1.jpg
Views:	2146
Size:	64.6 KB
ID:	96178  



mark post as helpful recommend reputation points    Reply With Quote
Old 06-13-2009, 07:00 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #2 (permalink)
Probationary Member
 

A80Avant's Avatar
Registered: May 2009
Tech Posts: 17
Reputation: A80Avant is an unknown
here are 2 more maps i have found but i am not sure what B85 and E85 mean when it comes to HX super40




mark post as helpful recommend reputation points    Reply With Quote
Old 06-13-2009, 09:38 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #3 (permalink)
Proven Member
 

JayRolla's Avatar
Registered: Feb 2006
Tech Posts: 5,075
Photos: 5
Classifieds Rating: 7
Reputation: JayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthy
If I can remember right that turbo should flow 69lb/min.


____________________________
Jason~ Parting out my DSM!
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 06-13-2009, 03:32 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #4 (permalink)
Probationary Member
 

A80Avant's Avatar
Registered: May 2009
Tech Posts: 17
Reputation: A80Avant is an unknown
Thanks! that clears a few things up...

now a more interesting question is what to tell people that 'advise' me not to use this turbo because it is a diesel turbo... and someone told me also that it will give me High EGTs with small amounts of boost...because it is a diesel turbo....

doesnt make much sense...

mark post as helpful recommend reputation points    Reply With Quote
Old 06-13-2009, 09:13 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #5 (permalink)
Proven Member
 

grimdsm's Avatar
Registered: May 2009
Tech Posts: 76
Classifieds Rating: 0
Reputation: grimdsm is an unknown
Send a message via AIM to grimdsm Send a message via Yahoo to grimdsm
what would that be in cfm?

mark post as helpful recommend reputation points    Reply With Quote
Old 06-13-2009, 09:18 PM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #6 (permalink)
Proven Member
 

JayRolla's Avatar
Registered: Feb 2006
Tech Posts: 5,075
Photos: 5
Classifieds Rating: 7
Reputation: JayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthyJayRolla is extremely helpful and trustworthy
Quote:
Originally Posted by A80Avant View Post
Thanks! that clears a few things up...

now a more interesting question is what to tell people that 'advise' me not to use this turbo because it is a diesel turbo... and someone told me also that it will give me High EGTs with small amounts of boost...because it is a diesel turbo....

doesnt make much sense...
WHAT!! Dont listen to your buddys. Put that bad ass turbo on your car and show them why a diesel turbo is more efficient. People are seeing faster spool than a gt37r garrett that is ball bearing with the same or more airflow. Also these turbos are very efficient. They dont cause high EGT's and are great pump gas turbos. They have instant spool on diesels and usually 20+ psi by 4k rpms on our dsm motors. Guessing yours will spool it real fast. Im actually going to be running the hx40 8/12 blade that spools a little faster than your beast. These turbos are starting to take over the dsm scene and for good reason.

Here is some good info.

Summary provided by wiseman, Dsm-onster:
HX35:

The 8blade hx35 has a 56mm compressor inducer. This is found on 1995-1998 cummins manual pickups. The compressor flows 52 lb/min according to the compressor map. The bolton BEP housing (0.55 a/r) is enough to push the limit of the compressor. There's several 500whp 8blade hx35 cars out there with the bolt on housing. It reaches 20+psi by 3500rpms in 3rd with 272 cams. Smaller cams would equal a faster spool speed in most cases.

The 7blade hx35 has a 56mm compressor inducer. This is found on the 1999-2002 cummins manual pickups. The compressor flows 60lb/min according to the compressor map and logged results from a member here. The bolton BEP housing with the hx35 turbine wheel do not SEAM to have enough flow to really reach the potential of 60lb/min. But many have logged over 50lb/min so far and seen 500whp. The stock hx35 12cm^2 twinscroll turbine housing is a t3 flange housing. This mated to a NON-divided runner manifold has produced a 132mph trap speed with a full weight 1g AWD. This is about 600whp. So the flow is there with the stock housing if you use a non-divided manifold. The spool speed of the 7blade hx35 is similar to the 8blade hx35 with 20+ psi by 3500rpms in the bolton housing and by 4000rpms with the stock housing with a non-divided manifold.

HY35:

The hy35 has a smaller turbine wheel than the hx35. And, it has a turbine housing connection that does not allow for a bolton housing to be used. It does not have a divided housing so any t3 manifold can be used effectively with this turbo. It has the same compressor as the 7blade hx35. We don't know if te hy35 turbine wheel and housing is enough to reache the 60lb/min potential of the 56mm 7blade compressor. Some one try it out already!!! It should at least be a faster spooling viable option to the full t3/t4 50-trim.

H1C/WH1C:

In 1994, there was the Wh1c which has pretty much the identical compressor as the hx35 but with a Vband compressor cover. The turbine wheel is the same. It will bolt into the BEP bolton hx35 turbine housing. It has 4 bolts at the housing instead of 6. So you will need to buy 2 more bolts and use 6 washers cut to make a flat side. Honestly, I just used bolts that were cut a little short and the bolt head was wide enough to pull the chra to the turbine housing. No sealing issues. Since the Wh1c is for all practical purposes an 8blade hx35 the spool and flow is the same too.

I have the big h1c. It comes on the INTERCOOLED 1991-1993 cummins pickups. It has the webbing for MWE but no groove cut like the hx35/wh1c has. This turbo I term the big h1c because it has a 54mm compressor inducer and same exducer than the 8blade hx35/Wh1c. The other h1c is the small h1c found on the NON-intercooled cummins pickups. This has a 50mm inducer but only 7blades and has no webbing for MWE. Less blades helps flow, but so does a larger inducer diameter. The most whp ever recorded on a gas 4cylinder with the small h1c was done on a KA24 nissan: 411whp. Since the big h1c has a 4mm larger inducer and the same turbine wheel as the hx35, it is safe to say that it flows enough for between 411whp and 500whp. The diesel sources state that it flows SLIGHTLY less than the early hx35. So 4lb/min less than the 8blade hx35 puts the flow of the big h1c at 48-49lb/min right where a 50-trim or 20g is. The small bep housing is all that's needed to get the most from the compressor and the spool speed is 20+psi by 3500rpms.

HX35-40 hybrid:

Keeping the long tradition of the marriage of sportcompact and hybrid turbos, there is the hx35 turbine and the hx40 compressor. It is strongly recommended to use the large bep turbine housing or the stock hx35 turbine housing with an non-divided t3 manifold for this turbo. The small bep housing around a t31 size hx35 turbine wheel is probably not enough to merit any of the hx40 compressor wheel upgrades. 20+ psi by 4000rpms can be seen in the hx35/40 with the hx35 12cm^2 turbine housing with a non-divided t3 manifold. With the large bep housing, spool times are to be determined. But likely similar.

HX40:

The 8blade hx40 has a 58mm inducer and flows about the same as a 60-1 (around 60lb/min) with ALOT better high boost efficiency and spool speed. It is the most common hx40 out there. The small bep housing with the hx40 turbine wheel is plenty to reach the full potential of the 60lb/min 8blade hx40 compressor. 20+ psi by 4100rpms with 272s.

The 7 and 6 blade hx40 is called the super40 and has the 60mm compressor inducer. This compressor flows around 69lb/min. You can get this wheel in billet style (think HTA). The non-billet wheel spools as fast as the 8blade hx40 in the bolton bep housing and has done 653whp at 40psi per the holset results only thread. Billet should spool even faster. The t3 .70 a/r BEP housing slows spool about 400rpms. But reports show a significant gain in flow per psi. So expect more power at lower boost with that turbine housing.

H1E/WH1E:

The Wh1e is like it's little brother the Wh1c. It mirrors the hx40 8blade in every way except that it has a v-band compressor cover and a 4bolt chra-turbinehousing pattern. It will consequently bolt into the hx40 bep bolton turbine housing and this is plenty of flow to max out its 60lb/min compressor.

The h1e is like it's little brother the h1c. There are different size compressors. . . BUT there are also different size turbine wheels too. Check measurements before buying this turbo if you plan on running a BEP turbine housing. There are lower flowing compressors than the 58mm 8blade that are out there. So this turbo may not flow any more than an hx35 if get the wrong one. You need at least a 58mm compressor inducer for this to be a worthwhile turbo vs the proven hx35 or 8blade hx40.

HX52:

This is a big sucker. It is commonly found on the Volvo Semis and usually has a billet compressor wheel. It flows 88lb/min. There is no bolt on housing for it. If you want a bolton housing for this turbo, then you don't want this turbo. In fact if you want a t3 flange turbine housing for this turbo, then you don't want this turbo. You DO want this turbo if you're looking at a gt4294r or gt4202r. The turbine inlet is slightly different than a t4 bolt pattern. You can still get the t4 manifold to work just fine by enlarging the bolt holes.

Misc.:

•Holset's don't spool slow. They spool faster than their garrett or mitsubishi counterparts. Diesel exhaust is cold and slow moving.
•The holset turbine wheel is a work of art. It has been shown to flow very well in a very small turbine housing. For example the hx40 turbine wheel in the small .55 ar bep bolton housing flows as much as a garrett gt35r turbine wheel in a larger .63 ar garrett t3 turbine housing. The hx40 with this configuration spools about 500rpms faster! You can upgrade to the .70 a/r BEP t3 turbine housing and have the same or slightly faster spool speed as the above gt35r with ALOT more flow per psi and consequently more horsepower per psi. This makes for VERY good pumpgas numbers.
•Holset patented map width enhancement. They do not have extended tip technology, but there compressors show more efficiency than their garrett or mitsubishi counterpart.
•They have superback technology witch leads to VERY, VERY durable compressors. The are designed to be overworked and underpaid.
•There are discrepancies all over the web concerning the compressor maps. Take what you hear/read with a grain of salt and a shot of tequila, and the worm.
•The holset is fine with stock 4g63 oil pressure from the oil filter housing. If you have no b shafts, you'll need a restrictor. The drain line is a garret bolt pattern. The feed line is different for different turbos.


____________________________
Jason~ Parting out my DSM!
View photos of this member's car 

mark post as helpful recommend reputation points    Reply With Quote
Old 06-14-2009, 12:49 AM Show Printable Version Show Printable Version   Email this Post to a Friend Email this Post      #7 (permalink)
Probationary Member
 

A80Avant's Avatar
Registered: May 2009
Tech Posts: 17
Reputation: A80Avant is an unknown
thanks!!!

i thought so!

i have been looking into the holset thread but cannot write in it yet.

im definitelly getting this one fitted!Its not going to be anytime soon,but a definite yes

will keep you posted

mark post as helpful recommend reputation points    Reply With Quote
Reply

Bookmarks

Thread Tools

 

» Recent DSM Photo
» Current Poll
How many times have you been to the Shootout?
1 - 40.00%
168 Votes
2-5 - 41.67%
175 Votes
6-10 - 10.48%
44 Votes
11-15 - 3.10%
13 Votes
16-20 - 4.76%
20 Votes
Total Votes: 420
You may not vote on this poll.
» Online Users: 818
233 members and 585 guests
Most users ever online was 1,704, 03-17-2008 at 09:11 PM.
DSMtuners Main Sections
DSM Forums
DSM Regional Forums
DSM Builds/Journals
DSM Articles
DSM Tech Guides
DSM Upgrade Paths
DSM Parts Reviews
DSM Vendor Reviews

DSM Classifieds
DSM Parts Guides
DSM Photos
DSM Videos
DSM Timeslips
DSM Dyno Sheets
Shirts & Apparel
DSMtuners Decals

Advertising Info
Our Sponsors
Site Rules
Terms of Service
Privacy Policy
Site FAQ
About Us
Contact Us

© 2014 DSMtuners.com - All Rights Reserved

DSMtuners is not affiliated with Diamond Star Motors. The Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, Mitsubishi Galant VR-4, and associated logos are trademarks of Diamond Star Motors, Mitsubishi Motors, and Chrysler Corporation. No, we do not hand out car sponsorships.

All times are GMT -7. The time now is 11:10 AM.


Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.

Search Engine Optimization by vBSEO 3.6.0