The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

looking for tripple a pillar pod

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

mikh338

15+ Year Contributor
163
0
Sep 3, 2007
niskayuna, New York
looking for a tripple pod a pillar guage pod for my 1g. now i want to try to find a pod that is the whole a pillar not just an autometer one that screws into your existing pod. i searched around on here to find other posts but didnt find anything. any help guys thanks
mike
 
1. Do NOT make multiple thread's about the same thing.
2. I looked for 5 second's, and found a dual pod full pillar... http://www.slowboyracing.com/estore/product.php?productid=1626&cat=5562&page=1

Couldn't find the triple though.

PS: I find the triple guage pillars to be more of a hassel to look up at a guage where as the dual keep's everything at eye level, and I can glance at both guages when checking my mirror's, and they have bezel's for the top vent's were you can place a guage there...still keeping everything at eye level.
 
1. Do NOT make multiple thread's about the same thing.
2. I looked for 5 second's, and found a dual pod full pillar... http://www.slowboyracing.com/estore/product.php?productid=1626&cat=5562&page=1

Couldn't find the triple though.

PS: I find the triple gauge pillars to be more of a hassle to look up at a guage where as the dual keeps everything at eye level, and I can glance at both gauges when checking my mirror's, and they have bezel's for the top vent's were you can place a gauge there...still keeping everything at eye level.

ya i had the vent one before but didn't like it to much, right now i have the triple holder that goes above the radio but i don't like that and want the pillar pod now thanks for the input
mike
 
I use to have a full 3 gauge A pillar on my 1G. Even with the seat belt track. I will try and remember where I got it from and get back to you.
 
Well that's stupid. :toobad:

I would call them back and tell them to take it off their website.

It's not listed as a full pillar on Lotek's site. It would say 'full' in the description if it was a full pillar. Also, if you look at the picture, you can see the end of the pillar (it is a little above the seat belt buckle, but is easier seen if you follow the top of the pod of the top gauge to the actual pillar).
 
I have the lotek tripple pillar in my 91 TSi AWD. Fitment was a tad tight due to stainless steel braided line from the filter housing, rubber boost/vac line and egt braided line.......It's tight but manageable....

Link to my picture

http://i32.photobucket.com/albums/d2/ZERODSM/Interior/7CobaltGauges.jpg

Best pic I got. It's not a full complete pillar but it overlays the stock pillar....I would recommend drilling holes in the stock pillar and route the lines and power wires through it...... Then screw in the lotek pillar, clean install...
 
I'm telling you right now, NO current company or vendor makes a FULL PILLAR triple gauge pod for a 1g DSM. There is a Double gauge full pillar or a triple A-pillar pod, that is the closest you will get.

I am currently looking to get rid of my Triple Apillar gauges however. I'm done with that 'fad'. Right now I'm trying to find the vendor who makes the 3-gauge bezel pods with the gauges pointed towards the driver, it's not just the flat insert one with 3 holes cut out, it's molded.
 
I actually have a 'full pillar' 3-pod sitting in my closet. The bottom goes all the way down, and the top cuts off just where the roofline makes its bend. Has room to trim away some of the plastic so that the automatic belts fit just fine. Got it in the dark gray color to match the dash area, not realizing that my pillar was light gray (and therefore would look kind of funny compared to the other one).

No idea who I picked it up from, would have to go back and look through my transactions from a year ago. Ended up getting the center vent 3-gauge replacement panel instead, on my end.
 
I actually have a 'full pillar' 3-pod sitting in my closet. The bottom goes all the way down, and the top cuts off just where the roofline makes its bend. Has room to trim away some of the plastic so that the automatic belts fit just fine. Got it in the dark gray color to match the dash area, not realizing that my pillar was light gray (and therefore would look kind of funny compared to the other one).

No idea who I picked it up from, would have to go back and look through my transactions from a year ago. Ended up getting the center vent 3-gauge replacement panel instead, on my end.

hey could you snap a pic for me i might be interested in buying this from you
mike
 
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Build Thread Updates

Latest Classifieds

Back
Top