The Central Hub for DSM Community and Information

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. This is where the DSM platform history is documented and archived. Log in to help us in our mission, and to remove most ads from the browsing experience.

wideband O2 sensor acting up? attached log

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

MotoEclipse

10+ Year Contributor
144
0
Oct 11, 2010
Medford, Oregon
So i finally got my car put back together with the new 5 speed. and i got the car running. i noticed it had a horribly rough idle. i checked everything. then came to the wideband. the ground had got disconnect somehow? anyways i got it re-attached. and my L.E.D Light on the sensor won't come on anymore. and the o2 is EVERYWHERE. check the log... idk whats the problem besides thinking the sensor went bad?
 

Attachments

You must be registered for see attachments list
Double check your LC1. Perhaps you need to simply re-calibrate it...Looks like you may also have a boost leak. I take it you are simulating narrowband from the LC1?
 
yea simulating. i have had the wideband in the car running good for about 4 months before the car was down due to tranny problems. so i know it had a good history. ill re-calibrate the lc1 tomorrow. and run a BLT

Ok i ran a BLT, and i had no leaks. i also re calibrated my wideband, along with test it by taking it out, and putting it a gas soaked rag. it had to problem.. but it's still acting up, bouncing numbers everywhere.... it still idles like shit too.. but revs fine.
 
Ill post the same info here as in your other thread on the same issue.



Your profile says you have 850s but your global is set to 0. That is way wrong. Fix thay and Im sure you will see an immediate improvement.

Set your global to -47 and dead time to 330 and see what that does for you.

^THIS^

Since your ground came unhooked I would recheck all your wiring just in case. Also if you powered the car on with the wideband controller unpluged/not grounded or whatever I would due a full new calibration including the heater circuit like you did the first time you hooked it up.
 
i dont have 850s in the other post, he read my wishlist. i still have the stock auto 390's.

im almost positive i have clogged fuel injectors. my outter cylinders are burning lean, and my middles are rich.
 
Add Value - Be Respectful - No Trolling - No Misinformation - Participate Often!
Support Vendors who Support the DSM Community

Latest Classifieds

  • Wanted 1991 tsi AWD auto engine harness
    Looking for a engine harness for my 1991 eagle talon AWD tsi auto trans If anyone has one hit...
    • sanmantsi72
    • Updated:
    • Expires
  • For sale 1997 eagle talon tsi
    I have a 1997 eagle talon tsi fwd auto for sale. It has 108k miles and in good condition.Recent...
    • El_marto
    • Updated:
    • Expires
  • For sale 1G DSM 4G63 PARTS
    Cleaning out my shop closet, Buyer covers shipping & fee.Parts:.20 Over Turbo 6-Bolt Block...
    • The_Partout_Spot
    • Updated:
    • Expires
  • Wanted 4G63 800cc injectors
    Im looking for a set of injectors that are at least 800cc. Thanks!
    • DSM_Thorpe
    • Updated:
    • Expires
  • For sale 2g 2g rear brace arms
    2g rear subframe brace arms. Missing one of the bushing spacers. No rust. Had someone looking...
    • Galant665
    • Updated:
    • Expires
Back
Top