AWDtalontsi96
10+ Year Contributor
- 144
- 0
- Mar 29, 2010
-
Enfield,
Connecticut
This is a unfinished project car. 80% complete. Doesnt drive and doesnt run.
Well parting out my project. 3 yrs and way to much invested , but times are tough and need the money. Will list has much as i can and throw up tons of pics for you to view. make me offers. Cell is 860-882-3553. Dave. Also looking to get 3K for the whole car. Rather just get rid of it in one shot then parting it out.
Okay this link works as in my last thread I couldnt get it to work.
Talon pictures by hondasilovers - Photobucket
Engine:
2.0l
Bored .20 over with Wisco HD 9.0:1 pistons
Manley H beam rods
ACL race bearings rods and mains
Arp main and head studs
Mitsu MLS head gasket
Stock crank balanced and polished to over 10K rpm
The entire motor was balance and blue printed.
Head Ported and polished , flow benched over 30cfm per port in stock which brought it 301cfm over all. Stock 1g heads flow about 271cfm
1mm ss over sized valve
Ferra intake and exhaust valve guides
Ferra Billet Valve locks
Ferra valve seals
GSC beehive springs rated up to 12.5 mm lift and over 11kprm
GSC chromolly spring seats
GSC titanium retainers
New 3rd gen lifters
New water pump
New oem timing belt , tensionor , pulleys
Balance Shaft removal kit
Oil cooler filter housing for running external oil cooler
Poly motor mounts
Tranny:
Basic Stage 1 build froom tre with double syncros in all gears
ACT 6 puck clutch w/extreme duty pressure plate
New oem slave cylinder
New oem Master cylinder
Misc:
Ebc brakes all around
walbro 255 fuel pump
fuel pump relay mod
battery relocation kit
tokio 5 way adjustable
tons of parts cleaned and powder coated
new magnacore wires
over 2000 dollars invested in oem interior parts
Aeromotive fuel regulater
Whatever isnt listed and you see in the pics just ask about it and we will work out a price. paypal , or if ## local just come by and pick it up and pay in person
Well parting out my project. 3 yrs and way to much invested , but times are tough and need the money. Will list has much as i can and throw up tons of pics for you to view. make me offers. Cell is 860-882-3553. Dave. Also looking to get 3K for the whole car. Rather just get rid of it in one shot then parting it out.
Okay this link works as in my last thread I couldnt get it to work.
Talon pictures by hondasilovers - Photobucket
Engine:
2.0l
Bored .20 over with Wisco HD 9.0:1 pistons
Manley H beam rods
ACL race bearings rods and mains
Arp main and head studs
Mitsu MLS head gasket
Stock crank balanced and polished to over 10K rpm
The entire motor was balance and blue printed.
Head Ported and polished , flow benched over 30cfm per port in stock which brought it 301cfm over all. Stock 1g heads flow about 271cfm
1mm ss over sized valve
Ferra intake and exhaust valve guides
Ferra Billet Valve locks
Ferra valve seals
GSC beehive springs rated up to 12.5 mm lift and over 11kprm
GSC chromolly spring seats
GSC titanium retainers
New 3rd gen lifters
New water pump
New oem timing belt , tensionor , pulleys
Balance Shaft removal kit
Oil cooler filter housing for running external oil cooler
Poly motor mounts
Tranny:
Basic Stage 1 build froom tre with double syncros in all gears
ACT 6 puck clutch w/extreme duty pressure plate
New oem slave cylinder
New oem Master cylinder
Misc:
Ebc brakes all around
walbro 255 fuel pump
fuel pump relay mod
battery relocation kit
tokio 5 way adjustable
tons of parts cleaned and powder coated
new magnacore wires
over 2000 dollars invested in oem interior parts
Aeromotive fuel regulater
Whatever isnt listed and you see in the pics just ask about it and we will work out a price. paypal , or if ## local just come by and pick it up and pay in person
Last edited by a moderator:
