dsmlink not working

[freeman 188]

just bought eprom ecu and dsmlink but now my car won,t start with it ,even when I put the original chip back in .ecu # md165531 ,this thing had a blown chip in it ic 106 on the board I replaced it but still no go .is it possible the ecu is fried ,and what about dsmlink that was in it when the chip burn,t out .the part # is m5269l ,8 pin ,there is 6 of them in there .

 

[Dsm2Nv]

Maybe the chip burned out rechip it check the engine fuses if none of that works then its your ecu

 

[freeman 188]

just bought eprom ecu and dsmlink but now my car won,t start with it ,even when I put the original chip back in .ecu # md165531 ,this thing had a blown chip in it ic 106 on the board I replaced it but still no go .is it possible the ecu is fried ,and what about dsmlink that was in it when the chip burn,t out .the part # is m5269l ,8 pin ,there is 6 of them in there .

put my factory ecu in and it starts fine

 

[SmalltownDSMer]

Not sure if it's the same for yours but when I bought link I had the same problem. Didn't realize that the firing order needed to be switched, just switched around the wires and it started just fine.

 

[1992awdlaser]

I can't even tell what you are typing. Please use proper puntuation, spelling, and sentance structure.

SmalltownDSMer- The wires don't have to be swapped on a 1G.

 

[No_Skillz]

Injector settings match whatever injectors you're running?

 

[SmalltownDSMer]

I can't even tell what you are typing. Please use proper puntuation, spelling, and sentance structure.

SmalltownDSMer- The wires don't have to be swapped on a 1G.

Ahh yes, Good to know... I retract my previous statement.

 

[freeman 188]

shouldn,t this ecu work with the factory eprom chip in it . to clear things up forget about the first post for now . I bought this ecu with the dsmlink already installed in it ,the guy I got it from said it worked fine when he took it out ,even with one of the chips fried in the ecu ,he said it didn,t effect it,s performance at all . now when I tried it in my car it won,t start . what could be the problem

 

[freeman 188]

computer installed now, the car almost starts but it won,t stay going , any ideas

 

[freeman 188]

computer installed now, the car almost starts but it won,t stay going , any ideas

now I have my fuel pressure solenoid steady clicking with the dsmlink installed in with the ecu, is there something I have to change or setup in link ,

 

[robbo185]

mine did the same thing. Started fine with old ecu but not with link on the new ecu.

I had to back the biss screw out a bit and it started/ran fine.....no idea why that fixed it.

 

[freeman 188]

why won,t computer connect to car , getting Io failed .command timed out .using windows xp

 

[Detective Coating]

Have you set it to the correct comm port and do you have the key turned to battery?

 

[Colt4G63 also]

Are you saying it runs now, but with the fuel solenoid clicking? The fuel solenoid only energizes during cold starts to increase fuel pressure by blocking the engine vaccum from reaching your fuel pressure regulator. You could unplug it. If it runs with your other computer installed, and it won't run with the replacement ECU installed with a stock e-prom OR the DSMlink e-prom, I would suspect the replacement ECU. First off start by telling us what the number on the ECU that works AND the number on the replacement ECU. It starts with MD...

EDIT: Sorry I see the #s now. Hold on Checking.....

 

[Colt4G63 also]

Ok I read it again, but I need the numbers on the ECU itself. With that I can identify the year of each ECU. Not all 1gs are created equal.

 

[freeman 188]

I replaced the eprom in the computer ,part number m6111 e827 ,right where the dsmlink plugs into it , it is a square ic about 1" by 1" with 60 pins on it .now the car starts ,but won,t connect with laptop . also all other problems went away that were stated earlier .

 

[freeman 188]

I replaced the eprom in the computer ,part number m6111 e827 ,right where the dsmlink plugs into it , it is a square ic about 1" by 1" with 60 pins on it .now the car starts ,but won,t connect with laptop . also all other problems went away that were stated earlier .

I will put some pictures of ecu on later ,so you guys can have a laugh and scratch your heads .

 

[Colt4G63 also]

You should make sure it isn't a 90 ECU, because if so, you need to swap the wires to pins 14 and 6 on the 24 pin ECU connector. You just soldered a 60 pin ic chip thats only 1"x1" onto the board? Psycho!

 

[freeman 188]

I will put some pictures of ecu on later ,so you guys can have a laugh and scratch your heads .

how do I put the pictures on here ,thanks

 

[Colt4G63 also]

I always put them somewhere else, then copy the link from the address bar and paste it here preceded by this

You must be logged in to view this image or video.

Like this

You must be logged in to view this image or video.