The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support JNZ Tuning
Please Support STM Tuned

Auto EVO 2

This site may earn a commission from merchant
affiliate links, including eBay, Amazon, and others.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Car is finished and I've put some miles on it while touching up the tune. Just waiting for the storm to calm so I can get back to racing.

49703644518_8aa85ae8aa_c.jpg


49720626392_38db894787_c.jpg


49720308781_ee676e5caf_c.jpg
 
Switched to a small cell up front as I was experiencing pressure drop issues with lots of Gs.

50086983391_d7fe5c2ef2_c.jpg


Car went 9.2@150 which is a new personal best at west salem IFO (placed 2nd). Didn't get enough runs in to get the 60' knocked down from the 1.55. Best MPH was 155 (still on the S363).

switched from a single nozzle wet kit to a direct port
50092652087_2886814a17_c.jpg


Upgraded the rear axles to DSS 300m and had the rear diff inspected/refreshed while it was apart
50086398878_461c0a2052_c.jpg


50086983451_9d8f770fea_c.jpg


Some testing at SCT Indy
50163191291_02c78ee082_c.jpg


Gen 2 7285 going in to try and run the wcf super street min ET of 8.50 for stage 2 registration.
50163191631_907c1ab8d5_c.jpg


50162654393_ab35e692f5_c.jpg
 
Dialed in the 7285 on the dyno and then went testing at the track. It went 8.68@166mph but was not able to get the 60' down due to a small nitrous issue. Should be heading back in 1-2 weeks to get our 8.50 min et goal.



50211099386_5944cb6ff1_c.jpg


50211372692_ffa7930b34_z.jpg
 
Last edited:
Congrats! Huge jump from the BW 63mm. Plenty more room to go.

What boost and nitrous was that run? Dyno numbers? Also, what base fuel pressure?
 
Congrats! Huge jump from the BW 63mm. Plenty more room to go.

What boost and nitrous was that run? Dyno numbers? Also, what base fuel pressure?
Thanks!

The run was 53psi and some nitrous to the 1/8. Car made 617hp on a mustang dyno at 58psi (my car never reads high on dynos LOL). Base pressure is 70psi with a single set of 2150s.
 
Painted inside and then installed some carpet.

50505685701_d28d94dbf6_c.jpg


50505846377_d81808a904_c.jpg


50505846387_dd4a59e0a5_c.jpg


Cage certified
50505846202_19b8f49fc7_z.jpg


Went from the kiggly 2 tooth to the 12 tooth kit
50504973158_103c47b4a6_z.jpg


Electric water pump installed and plumbed
50505685596_65fbe6f8fe_c.jpg


8x dekas installed and plumbed
50504973173_a73d7d7b2b_c.jpg


Switching to a Fueltech. I went with the FT550
50504973228_8c69469c14_c.jpg
 
Last edited:
Do you worry about the non-silicone connections not providing any flexibility under engine shifting?
These clamp assemblies offer a lot of flexibility, allowing the pipe to move a little over 3/8" while still sealing. It also helps that my front engine mount is solid (watching the car on the dyno, the engine didn't move at all).
 
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned

Latest posts

Build Thread Updates

Vendor Updates

Latest Classifieds

Back
Top