The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support Morrison Fabrication

Search results for query: *

  1. Scrymerr

    Meth MAF wire

    Im working on my meth instol and I got GM maf and translator(2g)so my question is shoud I tap it in to GM side or DSM side of MAF wire?Thanks O yeah it'sLabonte MotorSports kit.
  2. Scrymerr

    Help with intake tube...

    I had an FP intake for a while, and it seems like was plenty thick to drill and tap for some hose barb fittings to screw into. Now, I am not sure I understand your question about where to tap, your choices are pretty limited...
  3. Scrymerr

    Fuse Box relocation ideas

    Putting the fuse box in the rear where the battery is, is an aweful idea. The fusebox connects to the front chassis wiring harness, so keeping it close to the front of the vehicle is ideal. Putting it inside the glovebox would not require too much extension of wires, however I think it would...
  4. Scrymerr

    need help with turbo ideas

    If you want a turbo that will bolt up with little to no fab work, this is not the turbo for you. It will require you to get a new exhaust manifold, oil lines, intake pipe, O2 housing and some more. I highly recommend going with a turbo that will bolt directly to the stock exhaust manifold it...
  5. Scrymerr

    Which turbo is better for me the FP 3065 or FP3052?

    Another vote for the 3052. Although after my first day at the dyno, I wasn't super happy with how things were going on pump gas, but the 3065 will likely react similarly. After buying my 3052, I thought for a moment that I should have went with the 3065, but I am happy with the selection I made...
  6. Scrymerr

    o2 sensor mods?

    If you would like to upgrade your O2 sensor, a wideband is what you would do. Factory sensors are there to keep the car running like it should. Although many simple engine management options can log the output of these factory sensors and give you some information as to how the car is running...
  7. Scrymerr

    dsm link question

    Correct. I wish I could take some pictures for you to show you what the inside of the different ECUs look like, and how to tell which is an EPROM by looking at the outside where there will be an extra letter 'E' printed on the sticker. EPROM ECUs tend to go for around $250-300 by themselves, and...
  8. Scrymerr

    dsm link question

    You will need a '95 EPROM ECU. This ECU has a factory chip in it, which will be replaced by your new 'DSMLink chip'. Essentially you can have the ECU socketed, which will allow for easy removal and installation of the chips in the future. This will allow you to use the factory chip if you wish...
  9. Scrymerr

    Handbrake cable issues

    It is not hard to do. I have not done it on a 1g, but it will be almost the same as 2g, I imagine. I had to swap out my e-brake cables when I did AWD swap. Unfortunately I cannot take any pictures for you at the moment. Anyway, remove the center console, and you should see a single cable running...
  10. Scrymerr

    Brake Booster Check Valve

    Thanks for the reply Turbosax2, that was perfect! I can highly recommend mcmaster as well. I ordered a brass check valve with a viton seat for $13 at 5:00pm on Tuesday and got it Wednesday afternoon (helps that they are in CA). I installed the valve today, and it seems great: no leakage when...
  11. Scrymerr

    Brake Booster Check Valve

    Factory brake booster line on a 2g is 11/32. I am looking for a nice metal check valve that will be more resiliant than the factory valve and either fit inline, or thread into the manifold. Something similar to the MKIV Supra would be cool. There were a few threads mentioning a stronger valve...
  12. Scrymerr

    AEM Wideband ?

    I ended up going with an Innovate.
  13. Scrymerr

    AEM Wideband ?

    From my experience, most muffler shops I have been to do have O2 sensor bungs. I am assuming there is just one main type, as when I asked if they had a bung, they did not ask for size/pitch; they just said they had it and sold it to me. However, if you have a stainless exhaust, a muffler shop...
  14. Scrymerr

    Blower motor

    My blower motor in my 1991 TSi AWD does not come on when I turn the fan control on. When I turn it up all the way, I can here a small silver cylindrical shaped relay click. I have checked all my fuses and do not know what to check next or what the problem is. Ideas?
  15. Scrymerr

    Type of Gas For N/T

    Chevron sells gas at our local airport; both 100LL and "Jet A". I looked up Jet A and got this: http://library.cbest.chevron.com/lubes/compprd9.nsf/0/24e1758e1be528c0882563ea005c3965/$FILE/LPA-20.pdfIt says it is kerosene based. I was just wondering though, are there any cars that take this...
  16. Scrymerr

    Chevron Jet Fuel

    Chevron sells gas at our local airport; both 100LL and "Jet A". I looked up Jet A and got this: http://library.cbest.chevron.com/lubes/compprd9.nsf/0/24e1758e1be528c0882563ea005c3965/$FILE/LPA-20.pdfIt says it is kerosene based. I was just wondering though, are there any cars that take this...
  17. Scrymerr

    Welding machines [Merged 9-7] welder weld TIG MIG

    The Lincoln welder I got comes set up for flux core, and includes a few spools I think, but also has the line and reg for gas. This would be something good to start with because if you ever went the MIG route, you would just need the tank...
  18. Scrymerr

    Welding machines [Merged 9-7] welder weld TIG MIG

    Whats your price range? MIG will definately be cheaper and easier to use and you will be able to do the majority of things you might want to. I paid just under $500 after tax for my Lincoln that came with regulator and everything. Then I bought a 40 size tank (filled) for like $120. Then I...
  19. Scrymerr

    tubular manifold question

    I don't really understand what you are saying- you don't make any sense. Point being you can tell me that you installed a stereo system in your car, and gained 10whp, but that doesn't mean anything. You are still wrong and need to learn how things work before you try and say something is better...
  20. Scrymerr

    tubular manifold question

    Yea, you are a ####ing noob and can't read. "How does a tubular manifold increase horse power? It would seem to me that the longer runners would make spool time increase."Go argue with garrett and quit being a ####. http://www.turbobygarrett.com/turbobygarrett/tech_center/turbo_tech102.html...
  21. Scrymerr

    tubular manifold question

    I think you guys are idiots. A stock, cast exhaust manifold will yield better spool. Exhaust pressure is needed to spool a turbo, which is going to take longer to pressurize, a small cast mani, or a mani with wider and longer runners. How the hell do you just think, "oh, duh, the tubular one...
  22. Scrymerr

    my block just came back from the machine shop!! i got questions and need some help!

    I don't know anything concerning the specs: what is OK, and not OK as far as wear goes, but you should clear up your numbers to make sense. Firs off, it is not .2mm pistons, 20 over would be .020 inches. This equals .5mm. If your cylinders are worn .06mm that is nothing, and I cannot see how...
  23. Scrymerr

    Carpet color

    I will continue my one-man discussion with some more info: http://www.auto-interior.com/eclipsecolors.htm#1998
  24. Scrymerr

    Carpet color

    I have medium beige and medium neutral, and it is neither of those. I am hoping it will be either biscuit or caramel. Anyone else have any input?
  25. Scrymerr

    Carpet color

    I had them send me 4 samples which I thought were closest and I didn't have any that matched. If you could figure it out though, let me know.Dan
  26. Scrymerr

    Carpet color

    Can anyone tell me for sure, without a doubt, which one of these colors is found in 2gb eclipses with tan interior? No speculation please, I want the carpet to be the exact same color. If not on here, is there anywhere I can get a tan carpet that will be exactly the same color as the factory...
  27. Scrymerr

    Is a puck clutch supposed to do this?

    It is not going to bend at all. There is nothing keeping the clutch disc from moving back and forth, so even if the fingers were bent, as soon as the PP is disengaged, it should release pressure from the disc.
  28. Scrymerr

    Phenolic Spacers

    They do flow better, but that is because the runners are larger. This would be useless because the ports on the 2g head are so small. Just bore the TB flange to 60mm.
  29. Scrymerr

    Phenolic Spacers

    They do flow better, but that is because the runners are larger. This would be useless because the ports on the 2g head are so small. Just bore the TB flange to 60mm.
  30. Scrymerr

    Phenolic Spacers

    Is your 2g head ported to match the 1g gasket (if so use the 1g gasket) if no, then why the hell are you running a 1g intake mani on a 2g head?
  31. Scrymerr

    Coolant/sludge/oil/drain disposal -- what do you do with yours?

    Although mixing it with a solid absorbant may be legal, I still would not do that. Think about where it is going. I am surprised the hazmat place wouldn't take it, try a local recycle place or try the hazmat again. Maybe just tell people from now on that instead of it being a mix, just say it is...
  32. Scrymerr

    Coolant/sludge/oil/drain disposal -- what do you do with yours?

    Although you are joking, I am sure there are LOTS of people who dump fluids illegally. That really pisses me off, very stupid thing to do.
  33. Scrymerr

    Coolant/sludge/oil/drain disposal -- what do you do with yours?

    Take it to a local recycling place. I don't know what they are called but I know there is a place in the city where I live that you can go to take old batteries, oil, chemical waste etc. so people do not dispose of it improperly.
  34. Scrymerr

    Fastener Torque Values [Merged 3-9] value tightness torques specs specifications

    So I assume the above poster is correct in saying when using ARP's the torque spec is 80ft/lbs?
  35. Scrymerr

    Question about SS brake lines I bought from Buschur

    Quit being nub status. Don't bump your thread. Measure the brake lines and call Bushur and explain the situation more thoroughly and or talk to a different person. How hard can it be?
  36. Scrymerr

    Which BOV? [Merged 3-8] what bov best bov

    Pretty much any BOV with an adjustment screw blows. Everyone I know with a type-S adjusts theirs every other day because its always making funny noises and not opening correctly under low boost and stuff. There is no reason NOT to get a 1g BOV. They are cheap, work well, and you don't need to...
  37. Scrymerr

    can i do this?

    wooooowwww.... I am pretty sure it is www.google.com and then you just type in MITSUBISHI GRAVEYARD and look what comes up! :rolleyes: They are also one of our sponsors!!
  38. Scrymerr

    Rebuild suggestions

    Thanks for the response, that makes sense. However, that still leaves one question unanswered: are there any longevity issues associated with a lightened crank?I plan to run crower rods on ross pistons and pay a machinist whatever it will cost to install those.
  39. Scrymerr

    Rebuild suggestions

    I just got a 6bolt motor with shot rings. The cylinder walls look fine. THe motor has about 60k miles on it. I am going to remove the balance shafts, as well as put crower rods and ross pistons .020 over in. I have a few questions though:1.) what are the pros and cons of lightening the...
  40. Scrymerr

    Custom Solid Motor Mount pics! no more hop...

    Thats a crapload of sparks for TIG.
  41. Scrymerr

    delphi or denso?????

    Well where can I get some good quality 950cc injectors? I had Denso 720s, but sold them to upgrade.
  42. Scrymerr

    BOV ? (not sound or recirc vs. atmos.)

    1g BOV or Tial.
  43. Scrymerr

    External wastegate

    You will need to either:A) get a new exhaust mani with WG flange, the WG itself, and have the flapper on your stock turbo welded uporB) take off the flapper, get a new O2 housing that allows for the WG, and the WG itself.
  44. Scrymerr

    clubmitsubishi's fmic?

    Trust me, that is the Johnny racecar one. Ask 1badtsi and Adam (I dont know what his SN is). The car in the 2nd pics is Adams, and its a Johnny racecar. You can even see the piping is different than the piping they pictured.
  45. Scrymerr

    Results are in! SBR3500 Review With Pics after 6000 Miles

    Well, to put this in perspective for you, the ACT 2600 is rated at just under 400lb/ft of torque. This PP supposedly has more clamping force. This product is designed for what the driver was doing and did not hold up to what it should have. Unless Prez admits to either an installation error or...
  46. Scrymerr

    Results are in! SBR3500 Review With Pics after 6000 Miles

    Damn man, that really sucks. Only thing you can do is research other options I guess.
  47. Scrymerr

    Be honest guys...

    I have nothing against AT, but I would not mod an AT FWD. AT AWD would be sweet- brake boosting and very consistant launches.
  48. Scrymerr

    leaky BOV causing higher boost?

    Apparently you have never had a boost leak. If boost is leaking out your BOV, yes the turbo will have to work harder to make the same PSI. However, just because the BOV is leaking, there is no way for the actual pressure in your intake system to increase.
  49. Scrymerr

    can't drill this out!

    Swapping bell housings is not too simple. you will have to take the whole tranny apart, and swap over all the races and shims into the new housing, and even then it might not be exactly to spec. Im sure it would be fine, but after going through that work, and having to deal with those 26mm (i...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top