I think it's great to see something different I've seen 4g63's in hondas but not the other way around, I like the origionality. Ill be following this goodluck on the build.
I have poly inserts in my tranny and d/s mount, the others are good. The lower bolt slot on the block for the rear mount has broken off, but still has the upper spot bolted on.
Yeah my other car used to jump, but this isn't just a jump, it's a bang, I feel like I'm gonna get whip lash when it...
I finally got my car on the road after putting my engine into this new shell. After driving around I noticed a hard jerking and loud bang while driving in 1st or 2nd gear at very low rpm's. It happens when I put slight pressure on the gas pedal, and when kept steady with slight pressure at low...
I have a 91 Talon awd with a 4 bolt rear. There has been a loud knock that I hear and feel in the rear end when I lift and engage the clutch into gear. I was told it was the carrier bearing bushings. I took the driveshaft off, and yes the bearings were totally shot. Luckily I have a spare which...
Is the blow off valve blocked off? I think you mean the port on the intake is blocked off? If the blow off valve is being vented to the air and the intake is blocked off you should be fine to drive it home. Many people do this and daily drive their dsm's, not saying that you should.
It will cause you to run lean in-between shifts, and possibly constant stalling. For some people there are no issues but it would be wise to re-circulate it. This is an easy and cheap fix.
Ok I realize something is wrong here. I followed the ECU initial setup video from ECMTuning. Injectors are dialed in, MAF is set for my MAFT, target idle is 900rpm's.Take it easy on me I'm still new to this, where should I go from here?
Update. I reinstalled the mac driver called FTDIUSBSerialDriver_v2_2_14, tried it again and no luck.
I took the eprom ecu out and installed it into my 92 awd stock talon and still same issues. The link is not brand new I bought it from a member here. The cable, and install cd are from different...
I have a v3 lite dsmlink I just bought. I have power to the car, key turned to "on", both ends of the usb datalogging cable attached. I try to click connect and keep getting, ports in use by "unknown application". And also no response recieved! I've tried both usb ports. I have a 1g and have it...
Don't know where this connector goes too. It's on the passenger side and it's origin is from the positive battery terminal part of the harness. It is 91.
Hey spaz5spd, I'm from the ct area as well. And yes honda's are everywhere! What are you doing to your car? You'll also see me on ccdsm, but under spragggsx.
Looking for a -8an hose with two female fittings to attach to my fuellab fuel filter with-8an male end to my fuel rail with -8an male end. Searched google but i'm having no luck.
I've read on here that people were still making big numbers on the stock fuel filter. I thought of this previously as well. Price wise the stock fuel filter looked right, if it would stoll give me to my goal. Would you prefer otherwise, what filter setup are you using for a 450 hp range? And...
How are you guys who are using the same setup, -8an fuel lines to connect to stock fuel filter. I can't seem to find an adapter that has a -8 male, and make end to fit into the stock 1g fuel filter anywhere.
Thanks sounds like a good idea. pBut yeah the picture is bad, the raidator won't mount at this point. And especially is leaving me no room for i.c. piping.
Almost finished putting this car together, and have run into this final issue of the bottom support for my radiator is bent inward. Any ideas on how to unbend this?
I purchased a SS 02 housing from forced performance, i also have the 1g punishment racing fmic. Has anyone used this setup and run into fitment issues with the lower driver side intercooler pipe not being able to fit because of the housing's dump tube being in the way? If so how did you resolve...
Alright i got the first 3 screws off of the center parking light. Problem is there is no battery at this time to use put my lights up. Is this where the other screw is to take it off? I have never taken 1ga headlights/parking lights off before.