Good morning everyone, I am replacing all the gaskets of my engine using an Ajusa kit. I feel a bit lost with all these gaskets with no id at all.Is this part of the head included in the kit?What is the correct torque patern for head bolts?

Bonjour a tous!Hi everyone,I have removed the engine from the car as I wanted to clean it properly and do a full gasket work. It has been a laborious task about removing all the dirt from the block, it was running for years with a leaking top gasket (that rubber black one on the top case)...

Hi,Well after having left my dsm for 4 years in the garage as it leaked a lot and was deployed abroad. Now back home I tried to ressurect it.Removed oil pan and oil sump filter. Cleaned and new rtv on oil pan. Fuel pump dead. New 255lph drop in. Fuse blow by new pump, new fuse and rewired...

Hi all,I was using a cheap chineese "walbro" clone pump for a time. I was deployed abroad for three years, and came back home recently.Car has been siting this time in a climate garage. Pump has become damaged due to corrosion.Car did not start as a no gas issue, and when removed the pump...

I have a few sellers who say that evo 6,7,8,9 have all the same front calipers.Is it correct? Can I use a evo 7 or 6 caliper with the mounting plate for my 92gsx ?

Hi,at some point I have broken the connectors of the thermostat and I have lost them. I need the info for these connectors, where or how to order them. these are 3 connectors, one is a simple faston conector, ok, nevermind about this one,but the two other I woulf preffer having the real...

arbiter submitted a new DSM Profile :Spanish 1G GSXRead more about this vehicle here...

Good evening,I finished my clutch work today on the 1G, and when I took it for a drive on the neighboorhood, I could not rev past 4K, no matter if wot, 50% pedal, or slightly pressed, it would not pass 4K with noise like missfiring. Spark plugs are brand new, installed with the clutch work. so...

Hi allI have been having a problem with my clutch since new transmision. I installed an upgraded ACT Clutch kit but clutch doesn't disengage. I have been reading these guides for master cylinder adjustment and discovered that my rod was just a few threads in.I mean, the rod coming from...

Just that, I've lost the bolt that fastens the dip stick holding tube to the engine, and I just wanted to buy another one at the local hardware store.What size/thread it is?

#################UPDATE####### Car now refuse to idle when cold #############################Hi to everyone.My car has finally started, but when it got hot, it stalled.Car has been sitting there for some years (almost for), and went to a complete maintenance schedule.All the following...

This is an acknowledgement post for everyone who answered all of my questions.I really appreciate all these little helping hands over this forums fopr the hard work. Since 2008 I have been making all kind of questions about the car, and in the last year, at a faster rate. I am not going to...

Hi all.I have an embarrasing problem. My car has been sitting on my garage for quite a long time now, and I have been making all the maintenance possible the past six months, in order to return to the streets. (Belts, fluids, all kind of rubber inspections and repairing a few wires)...

Hi to all, I am on maintenance of my GSX, and I don't have the car near of me to check this out.I am about to finish the timming belt job, and I am looking for a replacement of my accesories belts. I am not sure about this, if it has 2 or 3 belts.I think, one is for the Steering pump...

I found out today that I have a broken stud on exhaust side of my head.It's the outermost left stud of the exhaust side.I have read something about that outermost ones, are bigger than the rest, but it looks the same to me than the others.As usual, I have the same issue that most...

HiI am having a leak on the thermostat housing of the head.I don't know very well how to explain it, but it's the unit that holds several electrical connections and some vacum hoses. I was given back a replacement on a parts shop, but it lacks of some electrical connections.the...

I have a 92 eclipse, and I am doing the timing belt job.my balance belt tensioner was bolted with a completely loose bolt. I feel lucky that I was doing the timing belt after discovering such a thing.well, I have a question. perhaps my tensioner was not properly installed. should...

Just wanted to know it the CXRacing o2 + downpipe product I use to see for sale is a good deal.I want to replace my o2 housing asap, and for the money it doesn't look so bad, but I can't see very well if there is going to be a good enough upgrade in the o2 housing. It looks small on the pics...

Quick question, got a very good deal for a set rims.7.5 x 17 on ET40 or ET38. Will this get into interference with fender, or will pop out outside the vehicule? I mean, I don't want my rims to go farther than the fender.Does anyone know the original ET of a 1G GSX?

Hi guys, I want to install an aditional oil temperature sender, on the stock oil filter housing.Is it possible to install some kind of T thing, to have both the original pressure sender, and my new oil temp sender?

I am planing a full maintenance on my gsx. I am aware that some sellers on the states, sell oem parts quite well and for a very nice price, but I want to get a quote at the local mitsubishi dealer. However, they don't have the adequate software in order to give me part numbers for such a task...

I have a question, maybe very silly, but when i go underneath the car, I see something that looks like a catalytic, but I am not sure.My vin is 4a3ct64u6ne092131, but I am not sure of this, and wincaps doesn't help me much either.so, to be brief, the question is.¿Is the thing in the...

Hi all:I had some problems while assembling back my tranny during the summer (1g 92 gsx), and I broke one of the entry or exits of my charcoal canister.So, I am planing to remove it as it is quite dificult to find a suitable replacement. So, what is the best way to solve the problem...

I know what you are going to say... GM Syncromesh, Penzoil, etc...Where I live, I am unable to find things so sofisticated.I will try to be brief, without big explanations. auto parts store, oil section, 4 brands- Holy auto (Own brand) - Elf - Repsol - Castorl or mobil, depends...

Hi all:I was thinking about a ball joint puller as a new adition to the tools wall.I had some issues using more agressive techniques to pull out ball joint in the past, so I am considering buying this quite cheap tool.I am being offered three diferent models. Wich ones should fit...

I am being offered a transmision, and I would like to know if there is more than one kind of tranny for the 1G, and if there is, how can I know wich one is it.The transmission I am being sold is already out of the car, but mine stills on the car and I don't have the time to remove it by now.

The fact is, that last year, I had my tranny welded again as it had the bellhouse broken near a support.Today, No clutch. I have the slave cilinder to broke the are where it is bolted to the tranny. Lukicly the slave cilinder has no damage, but I'm going to have to remove the tranny, and...

HiI am from spain, and after a long wait, my turbo is at home.I'm preparing to install it as I have already taken out the exhaust manifold, so I am welcoming your wisdom.

I am removing the exhaust mani but with no success. The last bolt still stand there. I've read about removing the heat protector of the direction pump but I am unable.that's the bastard, here, standing on the mani, as if I was powerless against him.I think these two are retaining the...

Just on another thing (Swaping exhaust) I discovered that my belt doesn't look too tensioned beetween the two cams wheels.Car runs ok, and my uncle did the timming belt recently (3 months) and car has been parked since.How many teeths should have the timming belt? Is there...

I Have found an interestign deal on a 16G.What changes should I prepare on a stock 1G 92 Eclipse?I supose fuel is going to be an issue as well as ecu right?

Hi allI bought my car some time ago now, and I already discussed here about various issues I had since.Two weeks ago, I lost all my oil. I discovered it was the oil cooler where the filter is located, the ¿bar? (I don't know the word, it's the steel 24 bolt that hold the oil cooler and...

Hi, I have just received my kit of a master and slave cylinders for my 92 gsx.Was quite easy to remove the old slave, and found out that the rubber ring of the slave was totally aged and was leaking a lot! I will order later a kit to rebuild it in order to have a spare for the next time.My...

I just filled the clutch fluid a while ago, made 30 miles, and dead pedal again.I suspect that I do have a leak. How many parts are involved in clutch fluid actuation? I have looked for a guide to replace the slave cilynder, but the only one lacks of description. Could anyone help me?

I went to the junkyard this afternoon and I saw a big Renault Van, a Master series one. I saw the IC and I started puting it to the guts..The IC is 720mmx200mmx42mm. End caps are plastic, and hoses must be 2.5".What can I spect from it? I hope that despite of being only 42mm it should...

I was wondering to buy a Xenon HID kit for the car, but sellers ask me if it's a H1, H4, or whatever is it... I have a 92 GSX with 92-94 assembly headlight...What is the regular one, and what is the high beam ones?

Radio does not work until rev arrive to 3500 rpm. Alternator is dead?The ignition lock sometimes refuse to turn when I insert the keyTurbo oil return line leaks as much a bi*** does on a gym...Have a serious vibration on front axle when reving up from 2000rpm to 3000 rpm front axle...

hi all, my engine is starting to make an awfull noise.My local garaje has heard it, and says it come from the belts... He thinks about a tensioner, a pulley, or the water pump. Previous owner (I bought car last saturday) says the pump was recently changed, and the belt is due to a...

I can't remove the radio, and btw, there is something like an iron box there inside not very well fixed...PD: Does anyone knows what are these cables on the driver side?

I am looking to replace the head unit of my car, it's a "computer controlled deck" and a CD-Player, in a single unit, but looks like two of them!Looking throught ebay I have discovered two names for it A 1DIN head unit, or a 2DIN head unit. ¿Our car is fitted with a 2DIN unit? Is it...

Hi all, I have bought on friday my car.It's a Feb 92 GSX with LSD on it. When I insert the key in to run , the car beeps. I got on the following lights Check Engine (5 seconds aprox) A jail icon next to check engine (until I start) Battery Oil presure I think it's all.I turn on...