During a cold start, the car runs great and I can punch the gas and everything is nice and crisp. As soon as the car idles down from the cold start, the idle starts to pulsate. The idle pulsates higher and higher until it goes over 1500rpm and starts fuel cutting. During any acceleration at...
Call/Text 6026891321. Open to offers. Located near Ray/I-10
Everything is from a 1g AWD turbo DSM
6 bolt crank + rods still in block. 3 out of 4 good pistons- $50
23 spline awd trans from a 91 1g- $100
4 bolt rear end- $150
Aeromotive 10 micron fuel filter brand new in box- $42
6 bolt a/c...
Gauge cluster will not light up and none of the fuses are blown ( all confirmed). Speedo and tach do not work, however the right turn signal works. The emergency brake light stays on and gets brighter when you pull the e-brake handle, and dimmer when the e brake is not engaged.The stock...
I am selling a 2g water pump. It is made by NPW, the parent company of Aisin (which is the company that makes the OEM water pump for dsm's) It is brand new in box and comes with both gasket and O ring. I am asking $50 shipped to lower 48 states. Ships from Phoenix, AZ or local pickup
I am trying to install a couple Jaz racing seats in my 91 dsm and the stock mounting brackets aren't even close to what the stock seats use.When I place the seats where I want them, the back half of the mounting bracket rests upon a big bump where the stock seat was bolted to, leaving the...
I am swapping front cases on my car so the oil pump and all the stuff that goes with it must be swapped to the other. I am trying to reuse this 6 sided plug which is not on the other front case. This plug is on the opposite side of the oil pump and I cannot get this damn thing off. I've tried...
This thread is for the people who are doing a balance shaft removal and are having difficulty getting the balance shaft bearings back into place to block the oiling holesI would first like to state that I did the balance shaft removal, but I left the shaft in (not the one that was connected to...
Trying to do the first startup of my 1991 eagle talon tsi awd. We have spark, confirmed on all cylinders.I have brand new spark plugs and brand new fic 1150 cc injectors. I am using dsmlink.We have confirmed fuel pressure at the rail, but everytime we turn the car over, the rpms move...
I took off my stock intake manifold and I am installing a JM Fab SMIM. My buddy told me to take 4 nuts off my throttle body to remove it from the manifold. I don't see 4 nuts on this thing anywhere. How do I remove this thing without screwing something up?Thanks :pray:
I bought this car as a shell with a wiring harness, well now i have most of the car wired up and connectors plugged in. I havent been successful in my search to find out what these wires do. Please help!1991 eagle talon tsi awd. looks like it used to have a/c and power steering. I am not...
I installed both axles and was ready to slide the tcase on the driveshaft. It needs to slide on about 6-8 inches, well mine only goes about 2 inches in, then gets stuck. we wiggled it and pushed on that sucker, but had no luck.I haven't got out the rubber mallet yet because I wanted to see...
My current setup on my 91 eagle talon tsi awd is1. walbro 255
2. 1150 cc injectors
3. afpr
4. dsmlink
5. 60-1 turbo
6. 272 camsI am preparing to take my car to e-85 land. From what I have found here, it looks like the walbro is the weak link, but what power levels do u think it...
It is the rubber insert that goes in the bottom of the shock. Mine was all cracked and ate up when I pulled it off my car and needed a replacement without buying a brand new shockI have a 91 eagle talon tsi awd
I have a 91 eagle talon tsi awd 5 speed.I have a automatic starter from a 1g, that is 1/4" short of actually engaging on the flywheel.I went to buy a 2g awd manual starter (the owner wasn't sure) and I brought my starter with to compare. The starters were exactly the same WTF?Are...
I bought a 6 bolt from a guy. it was turbo and came off an automatic (13g turbo and small ass manifold). I am trying to get ahold of him, because i dont know if it was awd or fwd. The problem is that i am putting my manual trans on the motor. I took off the flex plate and the spacer for it...
I wanted to go for a sleeper look and i want to buy a n/a hood (ya the one without the bump) for my 1g (4g63T) dsm. Anyone ever tried it? Can i shim up the back of the hood and take off the upper timing belt cover to make it fit?Thanks!
I have to replace my inner cv boot on the passenger side. The motor is ready to drop in, I would prefer not to pull the shaft. I am trying to find a quick boot, but can only find the outer quick boots. Anybody have the hookups on this one? thanks
I own a 91 eagle talon tsi awd. I purchased an automatic motor and it still has the flexplate own it. I will be using my existing manual transmission and flywheel/clutch combo on this motor. I have heard that there is a bushing of some sort between the flex plate and the block that must be...