I have a 7 bolt light weight flywheel and an Ingen 2G intake with a MAF sensor. The flywheel had a pressure plate bolt hole strip out of it so I drilled them all out and put timeserts in it. The intake has one nipple missing so it would either tap it and install a barbed fitting or have a new...
Please don't make this a flame thread as I am not thinking of doing this seriously just passing thoughts thru my head. My Talon sits a little to low to the ground for me these days so I dont much like crawling in and out of it, and with no AC I don't drive it much anyway. So I got to thinking...
Ok... long story short I picked up a set of Ilumina shocks and springs about 8 years ago and they are starting to show their age, and it would be nice to be able to go over speed bumps without having to get that super special angle at really low speed. Plus I am getting tired of having to roll...
Been doing some looking but cant really find a definitive answer. I know the throttle body opening is smaller on the E2 but is there a flow difference?Thanks.
Sorry if this is in the wrong section, but... Car sat down for a few months getting repairs done. Had to fix a couple of exhaust leaks, one being a bad stud at the head. While the car was apart I had a FP manifold, the turbine housing and my o2 housing ceramic coated. After having put everything...
Long story short... My PC decided to try installing device drivers for my OP2.0 cable while I was in the process of using it to reflash my ECU yesterday. As of last night my laptop would start the flash process then after writing about 10 or so lines close the interface and I would get an error...
Sorry no pictures, my phone is giving me issues right now and wont let me upload anything. Anyway I was wondering if anyone knows how large diameter and how deep you can drill the head at the bottom left exhaust stud, (the 10mm one closest to the thermostat housing). It has already had a repair...
Sorry for the long post but it has been a while since the last time I was on here. Mostly do to the change in carer and a move from state to state, then the car was down for maintenance the last couple of months. I have been having an issue with my car that I need some advice with. So to start...
So I remember years ago a friend of mine had the big green book for his old first gen MR2. In that big green bible of knowledge there was a section in the chassis section showing where to take measurements to determine if the frame was bent. I have the downloaded factory service manuals that are...
So I am having a bit of a problem and am looking for suggestions/ideas to see if I am looking in the right places. I had the car down for maintenance for a few months while I did a few things, (rebuilt the transmission, replace flywheel, had AN fitting welded to oil pan) the hole process took...
Sorry for the long post but I am looking for some information on logging my Wide Band http://wbo2.com/2j/2j1.htm using Evoscan and my OP2.0 cable and the DSM ecu.Here is a little background first. For a long time I had been running an EVO8 ecu in my car but had always had tuning issues...
Long story short (I will elaborate more later) my car won't pass emissions. The car is a 95 talon AWD so the state of AZ can't do the roller test only the exhaust sniff and it keeps failing for high hydrocarbons. I believe it is primarily due to the fact the my car wants to run in the 17:1 -...
Looking for a bad manual transmission mount (passengers side) I need one to install the urethane insert into. I would rather not tear up a perfectly good mount.Mike.
Just looking to see what my car would look like as my wife suggested. In the pic it still has a 2Gb eclipse front bumper on it however for the purpose of the photo shop request this pic will do fine. I originally was going to paint the car in the factory talon fashion (black top and the bottom...
Is it possible to do without damaging the plastic? The center section of my talon tail lights were painted by the previous owner and I am not too fond of the look anymore.
Hey fellow LV DSM'rs. I am in need of a MAF sensor for troubleshooting for about ten minutes. I am having trouble with my car and just want to narrow it down. First car started running lean during WOT, I looked at the log and noticed that the MAF signal was maxing out at 1600hz by 4500 rpm and...
Made something I thought I would run by you guys for ideas. I have been up inside my passenger door at least 3 times in the last 4 months to tighten up the forward window guide bracket. I realize there might be something else causing the guide bracket to loosen up this frequently, maybe window...
My father-in-law will be coming up to Las Vegas for a visit over the holiday and I have been looking for a GB talon front bumper. If there is anyone in Phoenix that is interested in a trade I can pull the 2GB Eclipse front bumper and headlights off my car and can have my father-in-law bring it...
Ok. So I did a quick search and didnt really find a lot on the subject but when I get home tonight I will dig a little deeper to see what I can come up with. In the mean time thought I would toss a couple ideas by the forum to see what you guys come up with.The basic idea is to see what...
All things considered I dont think it turned out to bad... I got the mill back from the machine shop a few weeks; I had to have the ways scraped down a little bit. When I picked up the mill it had been used so much in the middle of the X/Y axis that when you changed directions on the X axis the...
I posted this in the Las Vegas area Forum and havent gotten much interest in it and it looks like I may be asking a trip down to phoenix here soon (not sure when) so if anyone here in phoenix might me looking to swap let me know...Looking to see if there is any interest in a straight...
Looking to see if there is any interest in a straight across swap. I have a 2GB Eclipse front end on my Talon and would like to swap it for a 2GB Talon. Headlights and bumper cover.Thanks.Mike.
Question for my fellow EVO8 ecu users, could I get a couple of log files to compare against my logs please. I am looking for anything (cruse, idle, pulls) with timing logged.Thanks.
Having a little trouble trying to figure this out. I was given a profec-B but the wiring harness was cut short and is not complete. There are only 4 wires on the profec red, black, green, and white. Red and black I assume go to bat pos and neg, green and while go to the BCS however. In all of...
Specifically I am looking for the tool used to find the shim size for the pinion in the rear diff. The input seal on the rear diff of my car is leaking and to change it out I need to pull the pinion, while I have it apart there is a quite a bit of slop in the rear end that probably needs to go...
I am at the moment just trying to get an idea on what you guys have done to install the DIY coil over kits. I honestly could care less about the spring and upper spring seat I know what I want to do about that, I am more concerned about the threaded sleeve over the shock body. What brand did you...
I am done, I have had it, between this and my no boost issue this car has to go... I am ready to wait until I hear that @$$ H0!e down the street driving thru my neighborhood like a lunatic so I can take the e-brake off and push my car out in front of him and let the insurance handle it...
Without getting to far into what my reasoning behind being stuck on Turbonetics, just try to understand that "if" I decide to upgrade turbos this will more than likely be the rout I go simple do to where the money comes from and how much I can spend... So before i start I ask, PLEASES do not...
I am a bit confused here and need a hand. The only wiring diagram I have is for 95-96 vehicles for Canada with daytime running lights... I currently have a 95 US model Talon that does not have DRL and am trying to track down where the most likley culprit would be...When I have the...
Was just looking at adding in a switch for the map switching function on my Talon and wanted something that looked factory. What switch was in the bottom most position in the 2G AC vent? on every US model car I have seen it is filled with a blank. Is there an option on say a Euro model that puts...
It's dead and I have no idea why. All I know is that on my way home last night at about 10pm it was running great, I got on it a little and all of a sudden it started sputtering like it had blown an I.C. coupler. so I tried to get it to where I was able to pull over into a parking lot so I could...
Any one here in Vegas have a stock or aftermarket down pipe with a catalytic converter I can use to get my car threw emissions. I suppose if I have to I will purchase one but I really need to have my car emissions tested and I don't want to take it to a shop to have them cut up the 3" DP I have...
Ok. Did a bit of looking around and havent really found a good solid answer to my question. I just recently got my car put back together and now I am trying to track down all the little thumps and bumps. I got quite a few of them taken care of but now I am trying to hunt down the last one or...
I did a quick search and didn't come up with anything so I thought I would post this for all that ned a good laugh. I went to tuners thru it and let me say, it adds all the right words in just the right spots.Newbie Forum - DSM ForumsSamuel L. Jacksonizer - Surf the muthaf*ckin' web...
Just a quick update, when I have some more time I will get some more info up. It has been a long weekend and after paint, re-assemble, and finally my computer hard drive finally taking a crap on me it is back on the road. Now all I have to do is fine tune my idle a bit so it can pass emissions...
After many months of being upset and frustrated with my project and not really having the money to make any progress with it I have finally had my hand forced into doing something toward getting it drivable... since the last post I haven't really done a hole lot just a bunch of little things...
Just curious what some of you would do... My neighbor down the street commissioned me to put together a motor for his truck. It's a 95 Ford F150 4WD 302, lifted, big rims/tires, looks pretty decent but doesn't have enough power to get out of its own way (go figure). So after talking with him...
I have about 1/3 to 1/2 of a GSX conversion in the back yard. I was going to use it to convert a GST over but I ended up finding a TSI AWD. Now I would like to just be rid of the parts. I have the rear suspension/sub frame with the bolts that go threw the frame, fuel tank, and center...
well i think i figured out the reason my oil pressure gauge doesn’t work and if not then i am going to look into replacing the gauge all together with an aftermarket one. the doors are in work i am trying to get them put back together so i can get all the panels and glass lined up and back to...
I only fired it up twice last night but only for about 1 - 2 seconds at a time, it's not reading any oil pressure at the moment so I need to figure out whats going on. After the first time I fired it up it I checked the oil and it was low so i put some more oil in it, tried it again and the...
I know it has been a while since the last post so I suppose it is time for an update. For the most part it has been a lot of small "here and there" type work. The car is about 98% complete, well assembled anyway all the body work and paint still needs to be done. All the intercooler tubing...
jumped on EvoM last night and this is what i found...Speed Density 2.0 (3D VE Tables, Baro) - evolutionm.netNew 3D VE Maps SD Rom - evolutionm.net:rocks:it looks like it is still in its infancy and still being tested, but it is here! now i just need to get my car running so i can...
i have a set of grey leather seats front and back sitting in storage at my house down there in phoenix where my father-in-law is living. it has been a while sense i have looked at them but they aren't in bad shape just the drivers seat showing the most wear (sorry i don't have any photos ATM)...
need some advice if anyone has any... i have a spare transmission that started taking apart to rebuild (the guy i got it from said it was grinding in third). i have it for the most part apart however the center diff is stuck on the output shaft and i am having a hard time removing it. the trans...
according to the e-bay ad, this exhaust will fit both a GXS and a GST. :rolleyes:ROFLthink if i order one and try putting it on my TSI AWD they would give me my money back when i send them pictures of it not fitting?1995-1999 MITSUBISHI ECLIPSE GSX GST 3" TURBO CATBACK - eBay (item...
as promised some more pictures.most of the dash done. just need to get the steering column in place and lined up with the rack, install everything under the center column and paint that and that should put me about 90% done with the interior.one of the previous owners decided to...