This is interesting to say the least... whats the et record for a completely stock motor? How long before you get this car done? I know a completely stock engine car that will run with it. ;)
Also check your compression. You should also degree the cams. Did you set the preload on the hla's? A lot of times cams need some tweaking to get the potential out of them.
There are no back to back results on a dsm, correct, but as far as the question of airflow without doing anything but the wheel swap, there are answers as the wheel alone has outperformed the stock wheel in every app it has been tested on in real world dyno and competition areas.Unlike...
The "waves" in the wheel actually increase surface area within the same area of the stock size. These wheels have been done for months, Im suprised it hasnt already been in a DSM. There is already proven results in work stock class diesel pullers.
Hey guys. My name is Blaine Emerson. I just moved to the Hanover, Pa area. I just wanted to introduce myself. I have an extensive background with DSM's. The past couple years I was with Bullseye Power as a builder. If theres anything I can do to help with your build or just to talk cars PM me...
The compressor wheel looks good. Do you have a close up of the turbine wheel and the turbine housing where the wheel sits? It appears it has been rubbing in that housing but it could be camera angle/flash. Either way we still have some of these housings available.
Hey guys Blaine from Bullseye Power.. To answer any questions on feed we require a -4 an feed line. Oil Pressure must maintain at least 60 psi at the turbo at normal op rpms. If a restrictor is necessary do not use one smaller than .080
Hey Guys.. Lately Ive been machining GM maf sensors to help eliminate boost leaks at this point in the intercooler system.Basically what I have done is machine the "notch" out of the sensor and gave the clamping area more width and depth. This provides a better sealing surface and clamping...
Hey guys Blaine from Bullseye Power.. Ive been working on a Vband setup for my 1g Bracket car.. This is what I have so far.. Our own stainless cast manifold with a vband outlet into our s200 stainless turbine housing with a vband inlet..The turbo is a billet S259.. The "o2 housing" IS TIG welded...
Hey guys just thought Id show an actuator setup i built for a customer last week.. I havent seen too many actuators on these that werent kinda rigged up so I did a little bit of fab and came up with this.. a laser cut bracket with an actuator with a 22psi spring and a little bit of welding on...
so what would you call the piston ring in the seal plate and the piston ring on the turbine wheel?on the contrary sir.. it would leak past the ring or seals as some people may refer to them..Compression test is your best friend :thumb:
the only way you can make it work is to drill a hole in the horizontal lever about an inch towards the engine side.. and this will stress the hell out of the forks which u will break w/i 5k miles..
I have a 1990 GST that has 91-94 cables and base. I just rebuilt a 93 FWD trans and I am going to install it. The axles obviously need to be changed. I also have a 94 AWD. I was thinking possibly either putting in those axles from the 94 into it or putting the cups on the axles I currently...
1995 eagle talon tsi awd
5sp awd
16g, COP setup, 450's appears to be stock pumpA buddy brought this car to me. The car at first had a slight miss at idle and while cruising. Then progressed into wont accelerate or even idle I can keep it running by feathering the gas. Only codes that were...
ACT 2600/ Stock Disc
ACT Streetlite FWshimmed the pivot ball as far as possible so the fork doesnt hit the ppsystem has no airadjusted the master cylinder as far as i canstill couldnt select the gearput in the extended rod and can select gear and engagement is almost...
My question is about emissions testing and what not.. Where I live I have no inspections of any sort. Can anyone explain what the rules and laws are concerning inspections and emissions and where they are applicable.Thanks
i noticed no difference but didnt get a chance to dyno after the duals.. like i said i did mine purely for uniqueness.. the op did a great job on his as well..heres a vid of a quick run..http://www.youtube.com/watch?v=AnwR0I5GEgo