The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support STM Tuned
Please Support ExtremePSI

Search results for query: *

  1. 91tizzy

    Front suspension limit straps

    How did these work out for you?
  2. 91tizzy

    Cincinnati ohio area in need of oil filter housing by tommorrow!!! Help

    Any one is cincinnati tristate area that has a six bolt oil filter housing let me know and I can meet you tommorrow with money for exchange for a good one....Let me know what you got please !!!!
  3. 91tizzy

    Gs-t vs ms3 vs vr-4

    tell him to not touch any dsm....save them for me! He wants a mazduh
  4. 91tizzy

    1075awhp 3000gt ATX

    I appreciate the post brother and hope to see the car at the shootout as well...just remember for every jealous female that has posted negative about you there are ten other ppl that seen this thread and thought dam dude that is a hellacious setup and I appreciate what you ahve done with the car...
  5. 91tizzy

    Ebay oil catch can vs. name brand?

    Gofast If your still running a mass air flow system watch your fuel trims when using a vented catch can...lows and mids will be maxed out rich because of the unmetered air coming through the filter on the can going back into the intake at idle and partial throttle.Read the pcv thread posted...
  6. 91tizzy

    0 oil pressure = what long term problems

    Mits did that because of the two way street with oil temperature..shouldnt be too cold or too hot...the water to oil cooler helps raise oil temp for longevity of the engine etc...
  7. 91tizzy

    97 GSX Auto 350hp+ DD

    may need a few good supporting mods for 350 but... VERY GOOD ADVISE HERE...run the trans at full line pressure with some cheap injectors and logger with some way to compensate for everything and even on stock sidemount you could have a ton of fun
  8. 91tizzy

    low compression on the dyno?

    If its even and never smokes run it....130 is fine for an original motor...esp with cams
  9. 91tizzy

    laser gold package

    OP I WOULD KILL TO HAVE YOUR SPECIFIC LASER WITH THE GREEN ON GOLD...love the color combo
  10. 91tizzy

    Compressor Surge, FP3052 @ 25psi

    :banghead:FLUTTER AND SURGE ARE TWO TOTALLY DIFFERENT THINGS....flutter is what a recirc valve controls or eliminates when you slam the throttle plate closed after boost....surge is happening under throttle and load and thus much more damaging
  11. 91tizzy

    Compressor Surge, FP3052 @ 25psi

    Justin is far from a troll and contributes greatly to the community...in fact I would be very interested to hear his input on this and snide remarks would make anyone not even want to bother shedding light or information on the subject...at least anyone genuinly knowledgeable for that matter...
  12. 91tizzy

    Opened Up My Aeromotive AFPR Today!

    Fuel pump check valve should hold the fuel in the line...that would be where I would look
  13. 91tizzy

    Ported/Built BC filled head on 171,000 mile shortblock???? Opinions...

    Old thread but wanted to update now that it has been a while and I have a success story with it....installed the head and car was an insane difference....beautiful lope and with open exhaust it was very intimidating....installed a t3 tdo6h 20g and sprayed the car a 75 wet shot and made a lot of...
  14. 91tizzy

    Doing Some Good For Mom on Her Little DSM

    well thanks buddy..i figure that if its one thing I know I can do for her and really help out itll be with this car...she has always had little sports cars that I got to enjoy too (87 turbo sundance/86 z28/03 eclipse gts etc) so Im kinda giving back to her by making this car run and drive the...
  15. 91tizzy

    Doing Some Good For Mom on Her Little DSM

    Wanted your guys input on this even though I pretty much have set whats going to be done....Let me give some background....mom bought a fwd auto turbo 91 with 192000 on her...paints a little faded but it was completely unmolested...I was living in MS at the time and couldnt help her out with...
  16. 91tizzy

    sneak preview (photo inside)

    good luck this year Drew!
  17. 91tizzy

    Shift Knob Showoff

    Here is my cue ball....works great with the shifter thats in it
  18. 91tizzy

    How did you route your gauge wires to the engine bay?

    steering column boot...no ghettoness in sight for me as well on all of my dsm's
  19. 91tizzy

    Trashed turbo opinions

    dude as much as it seems like you dont want to face this fact....something obviously got sucked into the compressor and probably proceded on into your motor....sorry dude
  20. 91tizzy

    What did you do to your DSM today?

    enjoyed driving to and from work while adjusting the bov on my new awd five speed laser (evo3 16g, 2g mas, 550s, front mount, greddy style bov) runs amazing for this cheap ass setup@ 10psi....priced new axle and seals cause its leaking like a quart of tranny fluid every 2 days....praying its not...
  21. 91tizzy

    Can Fuel Pressure Be Set With Engine Off?

    thats why you pull the vacuum line off the regulator dude
  22. 91tizzy

    almost a 16 second turd!!!

    the sixty foot time may have been slightly better if I had tried to launch the car....like I said this was a fun run so I was just toying with it and didnt even try to launch the car....the stall I am going with is a restall that was done by a local here...should flash to around 3500 and build...
  23. 91tizzy

    almost a 16 second turd!!!

    lol nothing at all its on the stock converter....i have a custom converter ready to go in and I didnt feel like cooking the tranny tryin to stall it up for ten minutes to build a pound of boost....so i said to hell with it and ran that just playin around....she was rippin the 1st to second gear...
  24. 91tizzy

    almost a 16 second turd!!!

    Took my car to the track for shits a giggles.....figured some of yall would get a kick out of this...setup is a pte scm 6031 280s stock converter awd auto and a little e-85 mix on some 680's stock high mile bottom end....ran a 15.5 at 109 mph at low to mid 20's for boost (internal...
  25. 91tizzy

    Wanting to learn another turbo car, I am a fan 4 sure

    hell yeah dude another turbo buick owner....im deeply rooted in these cars. not sure if you keep up with the nationals and the racing but im building a 87 limited dark rosewood car and am family friends with the likes of jason white, dave fiscus, lonny(owner of extreme automatics) and had a...
  26. 91tizzy

    Just got her home from t04E 50 trim install

    Just to update....turbo failed about a month ago out of nowhere with about 1/8 inch in and out shaft play....NO up and down play which leads me to believe comp surge is what killed it even tho I didnt notice any....was running around 30 psi spikes tapering to 27-28 and it was a little street...
  27. 91tizzy

    Big surprise with car progress

    its good to here about the new hardware dude:thumb: keep on keepin on with your dsm.
  28. 91tizzy

    "Ricey" Cars

    I agree completely god please dont ruin the talon....dammit why cant you want to replicate ja rules integra????
  29. 91tizzy

    Neks Upgrade w/pics :)

    Nice job. Even if it does have an issue at lease your getting your hands dirty. Albeit it would have been wise for a comp check as soon as you got the car. This could have saved you the money from your mods into fixing the car if a problem did present itself. Still though looks like it is coming...
  30. 91tizzy

    Hmmm....

    had the exact thing happen and went with a mishimoto aluminum radiator/gates hoses combo for 225 shipped....couldnt beat that. The mishimoto is a good bit thicker than stock and the top mounting rubber insulators had to be modified to fit it but overall it is nice.
  31. 91tizzy

    Timing at WOT

    .75 is to lean...I recently had a problem that was quite hard to diagnose and ended up being the wally filter sock had gotten clogged by loosened up rust in the tank after using some ethanol. o2 volts looked like yours.Now it could also be showing lean from the cracked exhaust manifold...
  32. 91tizzy

    Timing at WOT

    Man in all honesty I feel your experiencing phantom knock. You have checked the sensor? Mechanical timing in check? if everything is checking out then I would suggest bumping up the timing....power is in the timing....target around 18-19 psi and jack the timing up as much as you can (within...
  33. 91tizzy

    Partial Throttle Compressor Surge?!?!?

    sorry i dont have any input on this but I just had to comment on the state of your car and bay....very clean...nice job
  34. 91tizzy

    camaro dude buys first talon

    sell the maro....what year is it? depending on what it is you could get around 5500 or so easy....just imagine what 5500 bucks in mod and maintenance money could get you from where the talon is now.
  35. 91tizzy

    What are you spending your tax money on?

    Hopefully a high stall converter....4500 stalled/57mm garret/280 cam'd street car:sneaky:
  36. 91tizzy

    DSMer's Unite! Vote for the 1g!

    90 gsx and omni glhs:rocks::rocks::rocks::rocks:
  37. 91tizzy

    The Book of Eli.. *SPOILER*

    very good movie would like to discuss after yall watch...it is excellent.
  38. 91tizzy

    Finally, a good quiet muffler

    from the pics it does not seem very hidden....our exhausts are quite viewable from behind I dont see how everyone driving behind the car could not notice actually if its stock suspension or stock ride height. Oh well if it works and could be hidden then hell yeah:thumb:
  39. 91tizzy

    Finally, a good quiet muffler

    Is that thing in a ditch?Looks interesting but would draw aLOT of attention and way too many questions.
  40. 91tizzy

    STM Project "Tin Can" 91 TSI AWD

    I agree that looked like a beautiful car waiting to be restored....I had a shell that was just as clean minus the interior you could have HAD to keep that car from getting gutted (i wanna say destroyed but I know it will end up being a beautiful race car) just a shame to be seeing the clean...
  41. 91tizzy

    how to Read Knock V3

    try adding timing if it isnt knocking...the glowing manifold is usually a sign of fuel combusting inside the manifold due to LACK of timing
  42. 91tizzy

    Upgraded the Radiator & I can't get the temps down

    whats happening buddy!!! lol...What kind of mix you using coolant wise? what temps is link seeing?
  43. 91tizzy

    Ported/Built BC filled head on 171,000 mile shortblock???? Opinions...

    Yeah that is the plan anyway...im not tryin to go crazy with boost or anything but I would like to make a safe and legit 400hp out of the car as it sits and run some mid to low twelves....dont think the stock auto will be good for much more than that....I guess the bearings really arent picky on...
  44. 91tizzy

    Ported/Built BC filled head on 171,000 mile shortblock???? Opinions...

    I was planning on going with reground delta 272's until the opportunity to grab this head came up....and it is already purchased awaiting install...I have used synthetic since I purchased the car 3 years ago....It will hopefully get retired from daily use within the next year and at that...
  45. 91tizzy

    Ported/Built BC filled head on 171,000 mile shortblock???? Opinions...

    I have a "race" head that I purchased at an extremely good price...brian crower 280 cams, springs, retainers, and an amazing port job (as well as revised lifters)....head came off a 700hp car that slung a rod and the owner didnt feel like rebuilding it again.My car has 171,000 miles with...
  46. 91tizzy

    Some old papers I found.

    its crazy...my 91 window sticker was for 29,xxx bucks???All the other prices for even the newer model 2g's are for less.My automatic option was 1200 bucks too...that blew my mind
  47. 91tizzy

    no more viper

    I have been a mopar person my entire life but I gotta say it would be a difficult choice between a viper and a zr-1...I definately would have to have the supercharged ls-9:thumb:
  48. 91tizzy

    too small of turbo inlet gasket cause issues?

    Yeah thats what i was thinking....i just cant bring myself to use one of those stainless gaskets that can be "ported" to match do to me having problems with one in the past. I HATE exhaust leaks of any sort and the car does too. I have a gameplan and will be double checking clearances in the AM...
  49. 91tizzy

    too small of turbo inlet gasket cause issues?

    Ok so I have a precision exhaust side on my 60 trim turbo and the inlet is huge compared to the 7cm exhaust gasket. I have a heavily ported 2g manifold ready to go on....the 7cm oem gasket I just purchased (I use nothing but oem gaskets) is smaller than BOTH openings....how will this affect...
  50. 91tizzy

    13g auto project

    Bottom line___ 13g is good to around 18 psi with supporting mods.....automatics hold power much better stock for stock than 5-speeds..the oil/water lines at the turbo are smaller with the 13g compared to 14b/16g turbos....some miss-info that i wanted to clear up..as stated 25lbs per minute is...
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top