Knockoff Greddy Type-S
-the classic Greddy whistle
-never used
-came with PR FMIC kit
-seems to have the superior red diaphragm inside
-is missing top lock nut
-$25 shippedFor proper install configuration, see the below link:
https://www.evomoto.com/tech_articles.php?tech_article_id=7
4G63 OEM Timing Belt
-MD326059
-used for less than 20k miles
-belt is still soft and shows no signs of cracks
-$45 shipped4G63 OEM Balance Shaft Belt
-MR984778
-used for less than 20k miles
-belt is still soft and shows no signs of cracks
-$25 shipped
Never had any issues with clutch engagement or drag. Over the past week or so my engagement point has dropped closer to the floor and shifting has been sporadic. I adjusted the rod under the dash and shifting was great again. Today, I was getting locked out of 1st gear and after watching Jafros...
Let me preface this by saying I've been doing a lot of reading and I know this is a loaded question due to the amount of variables involved. Supporting mods in my profile should be up to date. Boost leak tested up to 25 psi (I was aiming to run 20 psi). Stock 7 bolt long block compression test...
I am wondering where and how everyone mounts their PTU with the Evo3 IM? I have the Evo3 manifold and the Evo3 coil bracket and there is no obvious place to mount the PTU.I searched and found examples of mounted and unmounted PTUs. From my understanding, the PTU should be grounded to a...
I am in the middle of rebuilding a 1g TB that I bought used. Not sure of any history of this TB. Anyway, I was about to remove the TB shaft and noticed the shaft seals didn't look like the stock rubber material. Do I have either a metal case or mil spec seals? Please see attached picture.I...
Just bought this throttle body recently. See attached pictures. I understand that I do not need these vacuum ports as I am not running an EGR. However, I noticed the little plugs are missing. Will this cause a boost leak? I noticed the nipples have been welded? Jb welded shut? Let me know what...
I have my intake manifold off and was looking at my knock sensor. There seems to be some black goo starting to come out. (Picture attached) This means my knock sensor needs replaced correct? I was getting pretty consistent phantom knock in the low rpms so I'm hoping this can potentially resolve...
I've been thinking about ways to increase the overall thermal efficiency of my cooling system. I understand ducting will reap the largest benefits, which is a project I am planning later on. Along with an Andrew Brilliant designed vented hood from Carbonetics.I was wondering if lowering the...
I have been looking for a set of RM Sway Bars for about a year with no luck. The ST Suspension Sway Bars do not fit with almost all aftermarket exhausts. Does anyone know of any other options for a 2G GSX?
I've been noticing the new fad for our cars is to get this front lip.http://www.ebay.com/itm/For-97-99-Mitsubishi-Eclipse-2G-DSM-Splitter-Style-Front-Bumper-Lip-GS-GSX-GST-/321991371790?fits=Year%3A1998%7CMake%3AMitsubishi%7CModel%3AEclipse&hash=item4af82e6c0e:g:iMMAAOSwKtlWqUwW&vxp=mtrI...
Was going to pick up a set of RM Racing Sway Bars for my 2G GSX but they have been discontinued. So it seems that the ST Sway Bars are the only reputable option left because I'm not going to buy ebay ones.I've been searching for more information on the performance of the ST Sway Bar but...
I have deleted my EGR system a while ago and have used the periphery bits to ignore all the emissions DTC codes. However, I have one code that pops up every once in a while, P0400 EGR flow. I usually just delete the DTC and after a while it comes back and I delete again. I tried looking through...
Been researching and preparing for my first ceddymod/ecuflash tune. Ran into a couple questions about dialing in my injectors.1. When I tune my injector scaling, if I either need to increase or decrease my injector scaling, how many increments should I increase or decrease it at a time?2...
I'm about to pick up a 98 GSX with about 50k miles on it.*I've been doing research and I understand that DSMLink/ECU Flash are the most modern and arguably better options, but I'm not here to discuss that.I want input on running this setup reliably as a Daily Driver. I understand that...
I'm a student low on funds and need to make a decision by the end of summer.I'm either selling my 99 420a and getting a GSX OR rebuilding my 420a with forged internals but meant to run as a reliable DD.Basically if someone can help me with the 420a, I'll probably just keep it. I do all...
Just moved to Virginia Beach and am planning on heading over to the local Cars and Coffee meet this Saturday. Any other DSMers planning on heading over?
As the title reads. I did both dry and wet tests and got these numbers starting from cylinder 1, near the timing belt to cylinder 4 towards the battery. Also, take note that these numbers are from a fairly warm engine, about 15 20 mins shut off so the results are not from operating temperatures...
This summer I will be parking my car in a parking lot that is outside with no cover from the sun. Anyone have any suggestions for ways to protect my paint and interior?I plan on washing as often as I can can (at least once every 2 weeks, every week ideally) and waxing at least once a month...
So sometime in the next month I'm making a 230 mile trip and want to make sure my car is in GOOD RUNNING CONDITION and to survive the summer. My car has made this trip once around 95k, and now I'm at 104k.I posted on 2gnt.com about a month back concerning my 420a's head gasket. Over spring...
Sometime this summer I am considering painting my rims either gunmetal/graphite, black, or dark bronze. If somebody could photoshop these colors on my rims it would be very much appreciated. Thank you!And if you only feel like doing one color, I'd prefer gunmetal, which is what I'm leaning...
I was wondering whether anyone recommends any shops near lancaster county that can look at my engine for some general maintenance. Or if anyone is familiar with 420a's that can help me with my engine? Thanks.
hey guys, i was wondering if anyone in the lancaster pa area is trying to meet up anytime soon and roll around or something. i don't really know anyone who owns dsms around here but am definitely willing to meet up. thanks