Looking to sale Prothane Suspension Bushing Kit For Galant & DSM ECLIPSE 95-99 FWD / AWD Red ! Asking 150$ shipped !I got the kit over 5 years ago never installed it. There are new bushings available now for the rear control arms. When i bought that kit it didn't come with it. These are the...
that was in 2014 ! Now i have this 2G Cylinder Head Freshly rebuild 3 angle valve job , new steal seals, resurfaced , hot tanked 400$ i can ship if you pay shipping.
Holset HX35W 7 blade Twin Scrow 12cm housing 350$Evo 8 Enkei Wheel With 245\45 Kumho Ecsta XS tires with 5k miles on them 800$2G Eprom ECU Socketed with Ecmlink V3 Full 700$1G Ksport Road Race Version Coilovers new used for 1000 miles before part out 1000$Tial Q Bov color Black new...
OEM 4g63 Evo Eclipse 7 bolt 4G64 Crankshaft STD size Micro polished , hot tanked , balanced etc 400$ SOLDEvo Eclipse 7 bolt 2.3 Stroker Manley H-beam Rods and .020 Over Wiseco Pistons 9:1cr and ACL bearings all Brand New rings, wrist pins, etc. installed ready to drop in 800$ SOLD1G2G 272...
I have more parts for sale , that are not listed in here. If you looking for something let me know i might have it.Quarter Master twin disk just got it rebuild 1000 miles ago with street Gear drive friction disks 800TQ , floater plates and , diaphragm. for 6 bolt AWD 1000$OEM 4g63 Evo...
I did remove the old wires , and ran another one from the gauge it self to the sending unit, and nothing . Is there a way I can check the sending unit with multimeter or something ?
I have month old , innovate dual function pressure and temp gauge , and the pressure just stopped working yesterday . Anyone had that issue before ? I am not sure if it the gauge or the sending unit problem. :confused:
Just got my Daily Driver Dynoed though i could share :) here is the run down pretty basic and fast tune i did on the way to the dyno. Just did 2 pulls no adjustments done while on the dyno.Car made 485whp @ 5580rpm and 468tq @ 5185rpm boost set to 30 it spiked to 33 then went down to 28 psi...
The car was not quite ready but here's my results .Setup 6 Bolt Block with Evo 8 pistons , Delta 272 HKS , 1600cc injector , single 450 walbro , hx35 56mm 7 blade version , tune with dsmlink v3 speed density and e85 boost 30 psi droppin to 28 , waste gate spring wont hold on high rpms...
These piston are 10.5:1 only in evo 4G63 :) in ours are only 10:1 , I have the same cr pistons but wiseco for my race build. Evos have 43cc combustion chamber and we have a 47cc , so we lose 0,5cr in our dsm 4g63s :)
Any questions about pricing or details about tuning,You can contact me here PM or cell 7025570062 if don't pick up the phone, you can always leave voice mail , or text message and ill get back to you shortly .FACEBOOK PAGE https://www.facebook.com/4G63PursuitServiceE85 Conversions
2G FWD...
I read everything very carefully. Just sharing ! not trying to say is your fault ! Not taking anyone side !I had case that cold start 70psi , warm idle 10\15 psi cruse around 50psi WOT 70 75 max oil pressure, no restrictor , New Holset H1E fail same as yours up less than month ! That was on...
to much oil pressure can cause the problem you have.Anyway , i use same method on my cars , or my customer cars , i always get
Turbo Oil Feed Adapter Fitting M12x1 5 w 1 5mm Hole Volvo TD04L TD04H TD04HL | eBayThis and drill out the hole little more depend on the oil pressure, if car have...
I've been dealing with Holset, for past few years. These turbos are extremely picky about oil supply or drain! Friend of mine went true 2 OEM hx35 and and one H1C, till he listened to me at the end about his turbo failures. He learn the hard way! Oil feed, drain even engine oil are very very...
New schedule is up. Unfortunately, #WestSideWednesday is on indefinite hiatus at Red Handed Tattoo Gallery. There will be security in the lot Wednesday to prevent any loitering. Last weeks noise complaints to Metro from the neighbors about speeding vehicles coming and going from the lot is to...
Damn ive must a miss that part ....Like JusMX141 , you will need head gasket job, and head resurfaced, if you lucky enough , if you oil temps were hot enough ... your engine bearings might have gone bad too.
Hahahha that is the funniest thing I've heard in while ! You seriously believe that .... LOLLLLLLLLLLLDo you know that 80% of the DSM's run on Ethanol these days ? And no the Ethanol will not come off the market !!!
Dude please , drift no drift, haters , you serious ! Guy wants clean DSM .. And urs just not what he's looking for no matter if its build or not.So Don't tell him that he is never going to find another especially build like urs.
The only DSM meets that happens in here , are on Wednesdays on west side of town Durango and flamingo. But it's random, sometime you can see 1,2 DSMs , sometimes you can see 5,6 ... It's hard to get everybody in same place at Certain day.