Hi everybody,
i just needs to activating the ALS for launch and i set the hold timing at 20* ATDC and REV it to 7k RPMs but only make boost around 15 psi on GT35 turbo . would you please let me know if there is anything wrong ?!
Thank you in advance.
Hey, I have this issues from 2 years ago and since i was super busy on my work then i couldn't find time to tackling anymore , but from the last week i starts again and checked many things .Why i said weird cause its changing its behavior each time we wants to getting starts , it means...
Hi,i want to talk about the problem that occured on fresh rebuilt 1g 6 bolt engine that the bottom end included : JE pistons , Manley Rods , ACL race bearings , OEM oil pump , OEM water pump, BSE kit , Polished balanced Crank , use torque plate , adjusted the rings gaps , plastigauged the...
Hi Everybody,I just want to recheck the timing belt/ auto tensioner and since i already installed the ATI damper when i wanted to remove the outer damper to remove the timing cover then there is a clearance issue between the outer damper and body and it seems its not possible to remove the...
Hi Everybody ,The clutch kit on this car is clutchnet stage 3 RED PP with clutchnet kevlar disc and ACT streetlite FW then i just replaced the old ones for New master , slave , shift fork , pivot ball that shimmed with 2-1.5 mm washer and adjust the pedal properly like the Jacks said on his...
Hi everybody,like the title said , 2 days ago after i finished the rebuilt project and wants to run the car , i just checked everything and ready to start but the engine crank and cranking and wants to start but No !!! the engine dont like to run , and i got 0042 fuel pump malfunction error...
Hi everyone,Today after finish some works on GVR4 project , i tried to install the battery and connect the battery jumpers to check the power wires under the steering for installing the gauges but there is a pita things appear again and its the SHORT on the wiring circuit , since i know the...
Hi everybody,is there any body have some pics from bad sensor ground on 1g ecu ? please show me as soon as possible because i wanna compare it with mine !Thanks
Ali viento
Hello,I have a question about FP intake and 2g mass , is the 2g mass diameter needs the 3.5" or 4" coupler , if i wanna use FP intake to 2g mass , i need 4"-4" coupler or 4"-3.5" coupler ?please let me know ASAP.
thanks
hello friends,i wanna buy the turbo for the project of +500 HP , the piston compression 8.3:1 and the camshaft is 272/272 HKS plus the engine is 1g 6 bolt 2.0L .
Im hesitate between HX40 or HX35 or PTE6162e journal bearing or PTE 6162er ball bearing GT30R or GT35R . i need the fast spooling...
hi everybody,
i just want to buy the AFPR kit for my walbro 255 fuel pump and 880cc injectors but i dont know which regulator is better for me ? i checked the aeromotive website for fuel pressure range of the regulators , it shows me the 13105 range 35-85 psi and 13109 (A1000) 40-75 psi . is it...
Hi everybody,Now i need to know can i run the Auto Wiring harness 1g turbo on Manual engine/transmission and Manual ECU .
I want to change my Manual damaged 91-94 1g turbo engine wiring harness with Uncut Auto 1g 91-94 turbo wiring harness .
There isnt need any modification on using Auto...
Hi everybody,is the FWD 1g turbo 91-94 wiring harness same as the AWD 1g turbo 91-94 wiring harness ? i really want to know this , because i already have MD166262 AWD ECU and i want to know can i run it with FWD wiring harness or not ?Thanks
Hi,I want to buy the race camshaft for my 4g93 OHC engine (1.8 8 valve ) .
where can i find it ? is there anybody know the company that made the race camshft for this engine ?thanks
hi everytbody,
i found the 90 1g engine wiring harness but my 1g engine wiring hanress is 91, whats the difference of between 90 1g engine wiring harness and +91 1g engine wiring harness ?thanks
hi everybody,
i need help about my microtech ecu and engine wiring hanress plus im in the middle of my project .
i bought the microtech LTX-8 with complete engine wiring harness and sensors like AIT, 3bar Map sensor , coolant with dash logger for my mitsubishi 4g63 turbo engine , plus i also...
hi everybody ,
i want to know the works of some wires on my wiring harness , can anybody help me ?
i already bought this wiring harness and microtech ecu from the dsmer , but he cut some wires on connectors that he didnt use them and some sensors like IAC , knock sensor .
another question ...
hi,i need to buy the throttle body shafts seals for 1g throttle body ( vr4 ) and the 2bolts on the shafts because mine is damaged when i removed them .please let me know ASAP.
thanks
i want to buy the new wideband ( A/F ratio ) but i need your opinions , i want to choose the wideband between AEM & Innovate & Zeitronix .:confused:
please let me know which do you recommending to me ?
thanks
hi everybody,
i bought the used ignition system and i want to hook them now , its included :bushur racing Coil On Plug , MSD DIS 2 . plus i bought the engine wiring harness that works with them .
the BR COP has 4 wires ( 1 purple for 1#4 , 1 yellow for 2#3 , 2 red wires ) .
i really dont know...
Hi everybody,
i want to know your opinions about FP3065 turbo , i have this turbo and i really love it , its worth Penny of Penny .
please let me know your opinions .
Hi,I really confused to choose the correct pump for my car but i really dont know that my car is 2g or 1g , plus i dont know the difference of between GSS341 & GSS342 , i want to see some pics from the difference of them , is there anybody can help me ?
hi everybody,i want to install the custom fuel system that included :
Aeromotive A1000 fuel pump ( 600 lb )
Aeromotive A1000 Regulator
Aeromotive 100 Micron Filter
Custom Fuel rail with 2 feed and 1 return on center
Surger tank before the A1000 fuel pump
All the fittings and braided...