I purchased the wrong flange for the exhaust manifold and am past the return period so I am selling this brand new in box Garrett GT3582R Ball Bearing Turbo, T3 turbine undivided inlet, 3" V-band .82 A/R outlet. Compressor is T04S with 4" inlet and 2.5" outlet with anti-surge porting = $1500

I have a bunch of random stuff left over from a few different builds. Some items are band new in box. All in good working order when removed.*Brand New In Box* Garrett GT3582R Ball Bearing Turbo, T3 turbine undivided inlet, 3" V-band .82 A/R outlet. Compressor is T04S with 4" inlet and 2.5"...

NO PMs PLEASE!! Email - [email protected] clean 6 bolt head - clean = $500Ported 6 bolt head – $1500 (Fresh build, never been installed) Full Street Port with chamber work and milled deck 5 Angle Valve Job New Ferrea valve guides New Ferrea valves New Manley springs and retainers...

Stock 6 bolt head – clean = $500Ported 6 bolt head – $1500 (Fresh build, never been installed) Full Street Port with chamber work and milled deck 5 Angle Valve Job New Ferrea valve guides New Ferrea valves New Manley springs and retainers*New* Evo 8 Conical Valve Spring Kit with Custom...

What are the symptoms of valve float? Would I even know if I was floating valves?

I'm about to finish up my 6 bolt stroker in a 2G swap (DSM Forums - 6 Bolt '98 Eclipse 2.3L Build) and I just have a few questions before I can start it up. Any help would be greatly appreciated. Remember, this is a 2G with a 6 bolt.Where does the wideband O2 sensor (LC-1) go? The stock 2nd...

I bought my 98 eclipse a few years back and its always had wiring issues (poor running, dim lights, battery draining, etc). The guy took out an alarm and some gauges before, I took out the AFC since I have Link now and it looks like a 3rd grader did the wiring. Anyways, I don't know much about...

I am trying to install Fidanza adjustable cam gears but they did not come with any instructions. Below is a picture of the alignment marks. As you can see they do not line up and the teeth are off. Both gears are turned as far as they can inward without compressing the springs. The intake gear...

Where does this power transistor unit go? On the intake manifold? Its a 6 bolt swap on a 98 eclispe btw.

So I was looking at my oil feed and return kits for my GT35R and it looks like the feed and return flanges on my turbo are switched. Am I dumb or is this a problem? Is this turbo made for a different type of exhaust manifold or something or was it just built wrong?Thanks guys.

Got another update. I replaced the fuel pump with the walbro. It was pretty easy. I cleaned and painted the fuel cover. It was in horrible shape. The rust must have been 1/8" thick. I just painted over it since you cant order just the cover from the dealer. I got a new rubber fuel outlet hose...

So I bought the STM battery relocation kit (which came with no instructions) and I’ve been researching relocation kits all day and every post I read, I get more confused. Can someone please help me and anyone else who is not an electrical engineer figure out the whole thing? I'm sur eit's not...

Hey guys. This is going to be my questions thread for my 6 bolt swap. Any help would be greatly appreciated. This is my first build ever and although I know a decent amount, obviously I still have some questions. You can follow updates from my build here: DSM Forums - 6 Bolt '98 Eclipse 2.3L...

I finished tapping almost all threads in the engine bay and replacing them with new bolts. I grinded all rust away throughout the engine bay, under the fenders, under the cowl and treated it with rust killer then washed and coated everything with sound deadening undercoating. I cleaned all...

Here are some pictures to show what a piece of crap my car was before. I bought the car in San Diego but it spent its whole life in Chicago so there was quite a bit of rust. The front bumper was destroyed by running over semi truck tires on the freeway, getting caught on high curbs, and a lower...

Here are the details:6 Bolt Swap in ’98 Eclipse GSXHead: 1G Head Ported, Deburred, Deflashed, & Chamber Work Done By Me Head was Milled Flat Valve Job HKS 272/272 Cams Fidanza Adjustable Cam Gears Custom Conical Springs With Custom Titanium Retainers Ferrea 6000 Series Valves (1mm Over)...

I just got a valve job done and I need to know if I need to grind the valve tips so all valves have the same base to tip height. I haven't worked on dsm heads before, only subis. I have all the base to tip measurements and they seem to be off by quite a bit. I've looked through the maintenance...

I put the exhaust valve guides in the intake and vice versa. What are my options? Can I just leave them in as is? Can I knock them out and switch them without any negative side effects? Any help would be great. Any flaming would not be so great.Thanks.

I supposedly have two 1G heads but they are different. I need to know what the differences are for a 90-91 turbo head, 92-94 turbo head and 90-94 non turbo head. Or at least which two heads I have. So far I can see that my second head has longer cam cap bolts and visually the heads are very...

Do all 4G63 engines use the same main bearings? 1G, 2G, 6 Bolt, 7 Bolt, all Evos? I have some extra bearings laying around and my friend wants to buy them for his evo.Thanks

My left headlight was out so I went to change it and the plug on the harness is melted around one of the metal prongs and on the bulb where it connected to the harness. What could be the cause of this. Id like to get a new light in there asap so I dont get pulled over but the harness is pretty...

I found these vacuum lines going to nothing (the X's in the pic) What should I do? I tried to plug them with my finger while the car was on and it made the car idle poorly. The blue things are T splitters. Sorry for the crappy paint drawing.

Does anyone know a company that makes a turbo to cat O2 elim downpipe for a gt35r on a 6 bolt in a 2G? Im pretty sure ill have to get one custom made but i thought it would be worth asking.Thanks

Alright so I bought a GSX from this random guy and it was real shady and the car was modded a good deal but i didnt really know anything specific and the guy i bought it from didnt tell me anything cause he claimed it was his girlfriends and she was in Iraq. :confused::rolleyes: So it drove...

Does anyone know anywhere to get 93 Octane gas in the LA area? Ive heard rumors but never seen it.

I remember reading a post where people were arguing about weather ARP headstuds were strong enough to handle 500 HP and 30psi of boost but I cant seem to find it and Im going to buy new headstuds on Monday so Id like to know. My plans for the build are:2.3 Stroker 6 bolt in a 2G Daily...

So heres the deal,I love my car and I love working on it but I don't really know much about building an engine or swapping motors etc. I'm planning on doing a 6 bolt swap on my 98 Eclipse GSX but i dont really want to trust or pay someone else to do it. I really want to learn how to do these...

I have a 98 eclipse AWD and when Im making tight turns my car kind of hops and the rear wheels have to slide a little. Could this be my rear diff?Thanks

Hey guys Im planning on doing a full build and 6 bolt swap into my Eclipse GSX this winter or spring. I need a place to work with equipment and some help since I haven't done one before. If anyone wants to help me that would be awesome and Ill give you some $$ too. Let me know if you want to...

I may get the opportunity to buy a VR-4 engine as a swap into my '98 GSX. I know its a 6 bolt 4g63t but I was wondering is there were any other differences in that engine that would make it more difficult to swap. I don't know much about the Galant so I thought id ask before i wasted my money. I...

Ok so my 98 GSX is having problems (horrible idle, wont boost, all around runs like crap)and im pretty sure its because the guy before me wired the SAFC-II wrong, or atleast thats part of the problem. So i went on the Apex site to download the instrustion manual and its not telling me very much...

Has anyone had any experiences with this company?JDM Engine Corp http://www.jdmenginescorp.com/They offer free shipping anywhere in US and the price is pretty cheap too. Hopefully not too good to be true.Im thinking about buying a 6 bolt off them for the swap im planning but i want...

Does anyone know any good machine shops in socal? I'm planning on building a stroker later this winter and I need a shop that is reliable and detail oriented.Thanks