I see the wisemen are being reduced to spelling. It is a sad day. Aslan have you blown anything up lately? Turbo Guru have you finally got
your car running after the turbo swap?Pete
Was banned from another site and was lonely. Got a call from a
friend who said nice people and fellow DSMers were real. Checked it
out, and found out he was right. Thanks Nick!Pete
Clip the turbo for the top end power. Get a 2g ported and polished exhaust manifold (new from dealership $175ish). Port match to turbine housing and gasket match to exhaust ports from head. Clean all casting
marks on the inside of the manifold removing any rough or sharp edges.
This can be...
I am taking your lines? What about asking about fuel management for the ETE32. I told you that the DSMlink is being preprogrammed with the 650's for the ETE32. I also said you would need the Walboro 255 and a FPR. I did mention the spoolin up FPR, but have since found a better one.Oh, and...
The 18g and the FPbig28 will max out around 340whp. Get a turbo that
can give you @ least 470whp. You are going to beat the **** out of your car trying to get it to run 12's with either of the smaller turbos. Your car being a front wheel drive has to make more HP to get the lower times.Brad...
If a turbo is properly taken care of it will last longer than the car.
100-150k is where we recieve many rebuilds. This is 90% of the
time because of carbonization. If you use a turbo timer and keep
clean cool oil in the turbo it can last a lifetime. Cracking of the turbine
housing is normal...
Dyezak-
The level 5 or the ETE52 has the 60-1 compressor wheel and needs more exhaust gas. That turbo is meant for a car that has a ported head and built engine.
What modifications has he done to the car? What HP results did he get from the DYNO? You say the Mutt had more power and spooled the...
Reducing backpressure by use of a vacuum. The small amount of
backpressure caused by the turbine wheel does waste some engine power. The amount is so negligable that it is normally not taken into
consideration. To suck start the turbine wheel is an interesting idea, but
the vacuum would need...
Greg that does help, but he needs to see your first pass!
That was sick!
He takes you off the line and I felt your clutches pain.
That was the only thing he took you on.
You pounced on him like a cat.
It's at importevolution.com click videos.It is not my place to answer...
Go to home page look at the top and click on banner. We have added
more prizes to list that have not been updated yet, and are still
collecting prizes.We are also taking suggestions! What do you want? What is something
that would make you want to enter contest?If you have questions...
HP is determined three way.
Total volume of engine (displacement)
Revolutions of the crank shaft (r.p.m.)
Mean effective pressure in cylinder (m.e.p.)
HP=Displacementxrpmxm.e.p.There are many ways to gain HP you are concentrating on the m.e.p. !
Mean effective pressure of the cylinder...
A turbocharger uses expanding exhast gases to spin turbine wheel in two ways. It not only uses exhaust gas pressure , but also the heat energy. It uses two different forms of spent energy to increase the mean effective pressure in cylinder. If you are going to spend your time think about using...
Joe, I like your Stainless Steel downpipe nice piece. Do you have one that eliminates 02 housing? I also noticed turbos. Have you seen mine?
Would you like to help me and DSMTuners with a prize?
Enter contest. Win contest. Have my unveiled turbo and a full sponsorship for 12 months.If this is your first import listen to everybody, and make up your
own mind! Their are package deals to get everything at once
to make your car EXTREMEly fast that save money, but if you
are going...
The 16g is an OEM turbo designed to operate under factory settings.
He does not need to do any mods. He says his car is stock, the only
reason he would need to add mods is if he added mods.