Lucas, isn't there a waiver that you have people sign before you tune a car? I took my car in to a local shop to have it tuned, but they blew the composite headgasket I had on it. It could of been because of the tune or because it wasn't installed right. Either way there was nothing I could do...
Exactly. I just put on the mustang calipers. I painted those red, and the brackets black. The rear stock calipers i painted black.Here are some picsThis was the day of install and the metal masters were still seating
The vibration isn't that bad. I noticed when I installed my motor mounts that there was a more direct feel with the engine/transmission when disenguaging the clutch and overall shifting.
Check for more info. When is it overheating? Do the fans come on? How does the oil look? Does the car look like it was taken care of?It could be a blocked radiator, thermostat, fans, headgasket...etc.I would at least do a compression check before buying as overheating puts a lot of...
I never really wanted to gamble with a filter. STP doesn't even post their filtering percent on the box.I usually go with an OEM or at the very least a fram Heavy Duty filterAlso, your filter might not be the problem It could be you oil filter housing/cooler. Overtightening the...
I took apart the splash shield on the drivers side and found the whole section of wiring from the abs to the dash crispy! Some of the wires were melted together!Its definately been like that for a while though. I guess if finally corroded enough to where it gave me problems.I'm gonna...
Whats the problem? Have you checked the grounds?...done a voltage drop test to them?There is a 4 wire plug on the front of the alternator. The green and white go directly to the ecu...pin 33 and 41 The black goes to the generator relay then on to the tail lights. The red goes to the 40A...
I assume this is the 95 GSX with 6 bolt swap and not the 96 GSX listed in your profile? I also assume you put the 20A fuse back in for the following discussion?
Sorry, its the 96 Gsx/ 6 bolt swap. Yes the 20A engine fuse is back in.ACC key position does nothing so I assume you meant the...
95 GSX/ 6boltI am really, really frustrated guys as I'm sure most of you know how difficult wiring problems can be. This has been a week long, day in, day out process with no results. I seriously have headaches from all the countless thread I've read on electrical problems.My car has...
i replaced my 2 white wires from the alternator to the 100amp fuse with better ones. I also used 4ga and grounded the alternator directly....I used the stud that holds the bracket to keep the harness in place. Check you 4 wire plug. The green and white wires go to the ecu. Im not sure if it...
My 2g GSX WILL NOT START!Mods:Fuel Mods
255 walbro
Full Throttle AFPR
1000cc RC injectors
New FilterEngine Mods
6 Bolt ( perfect compression...as of last day it was running)
<15,000 miles on longblock
Wiesco Pistons
Scat Rods
264/272 CamsMagnus IM/ 1G TB (BISS out)
Maf...
newdsmtnr96...if your using an ebay turbo, it is suggested to use an oil restrictor on the feed line as the pressure will blow the turbo seals fairly quick. Good luck!
Well, quite a few have gone without springs and retainers for quite some time. I did numerous pulls with mine for about 10,000 miles.But that doesn't mean you wont float a valve.
Just thought I'd update. I still don't have the exhaust on yet. Im waiting on a cat, because the one i bought had a hole in it....Will it still work though? I know there are two screens...At the exhaust shop. Velezquez and sons.Here are a couple of engine bay pics of the...
someone was telling me its between a t25 and a 14b and it spools up quick. The last nt car was really fun to drive.I apologize for the wait too guys. I'm on vacation.
**The o2 housing and downpipe. I barley was able to get this in there with the ac compressor still in the way. I thought i might of needed to get a new manifold.In some heatwrapMORE PICS TO COME!!... of the finished product!
...but i need to make room for the intake**The cut up bumper supportWhat it looks like... I wish i would have gotten a 31" length instead. You can still see space to the sides of the intercooler
This isn't in the 420a section because I'm not allowed to post there yet.Here are more pictures.**Treadstone manifold and turbo togetherl.The turbo and manifold on the car
Hi guys,I own a turbo dsm myself but thought that I would give the 420a a try. I've already put on a turbo kit on a friends 420a before, but it was done rather quickly. I just followed the write up found here.Now that my brother was looking to turbo his 420a, i thought I would help...
Yeah, I'm down. I'm cool with even a mini meet. Where's a good place though? WHat about Lakehurst? When? When is it supposed to be getting warm again?...like above fifty?Any of you guys going to the devo tuning BBQ this Saturday? Maybe we could have a small get together and then all...
Yeah, we need something lakecounty only. slow99x you were there right? Me and ronnie were checking out your busted front lip. At first we thought it was supposed to be like that.