Okay, so here is the deal, 7-bolt motor rebuilt ~5000 miles, rebuilt trans ~1500 miles, tuned ~500 miles ago. About a week after my tune, I started hearing a clicking/ticking noise, the noise gets louder has I step on the clutch. I assumed TOB and took it to a shop to get confirmation. So I just...
After getting my car tuned, I drove it for about a week. I started noticing that the clutch sticks to the floor when I go to shift after hard left turns. When this started happening, I started hearing a clicking sound from the driver side engine, the click gets louder when I step on the clutch...
Well, I've recently had it tuned and its been fantastic. I drove it around today to run some errands and no knock. I drove home, installed some new speakers and an amp and then headed off to school. While driving to school, it just started knocking under normal driving/cruising :notgood: Anyway...
So I installed my walbro 255 today and now I have a fuel leak, well multiple leaks actually. So My question is why is it leaking? It didn't leak before I installed the walbro. Thanks in advance.
So I go to install my walbro 255, the o-ring is a bit loose compared to the o-ring on the stock pump, is this normal? I can't find a o-ring with a smaller inner diameter with the same outer diameter.
Hey guys, well I just got done attempting to time my car. I adjusted my 1g CAS while he looked for timing. We took it for a drive and noticed that the idle is stupid high, first it was 1500 and now its 2200. Every time I push the clutch in the idea goes back down. I used ecmlink to ground for...
I was testing the voltage and resistance of certain things that would apply to a no start. Anyway I have a 1g CAS in my 99, had it for a while and has worked fine until a month or so ago. Anyway the harness for the CAS tested within the values but when I test the crank position sensor I get 0...
Car wouldn't start one day, I tapped the starter and it started. Next day the car wouldn't start again, jumped it and it started. Third day, tapped starter, jumped it and no start either. Bought a new starter and it is engaging the flywheel, but won't turn it. Tried jump starting it with my...
Hey guys/girls, I was wondering if the convertible motors are the same for all spyders, also if the rear quarter window/assemble/motors are the same. One other thing, is the starter the same for all 2g m/t 7 bolts? The reason I ask about the starter is because of what it says on this site, it...
I know there are a couple threads on the topic but no definite answers. From what I've read I believe the 96-98 4 wire automatic Galant alternator will work with a 2GB, correct? Or will a manual one also work?
Hey guys, I'm looking at this 1g in town and it seems a little fishy. He says he has a 95 ecu in his 1g and I texted him and asked him how he converted a OBD-I to an OBD-II, but he never texted back.1991 Talon tsi awd turbo trade 1st person with 1100 cash can driveaway
Hey guys and girls, I just parked at school and notice there was a small stream of liquid flowing from under my car. I touched it and it appears to be cold water, I didn't have time to look under the car because I was already late to class, but cold water? Wouldn't water/coolant be warm/hot?
Hey guys, my clutch has been slipping for quite some time now and I finally decided to drop the transmission and I find that it's filthy, oil everywhere. My question is, is it more likely that its an input shaft seal or my rear main seal? It doesn't look like my rear main seal and it shouldn't...
Hey guys finally logging with ecmlink and I am noticing a lot of knock. 3k miles on fresh rebuild with wiseco pistons and manley rods, fp2 cams and FP bt28, 450cc injectors. Here is a log on my way to school (knock) and on my way back (knock2), was only at school for 30 minutes. All easy driving...
Hey guys I was wondering if anyone knows where to get the gst spyders rear speaker covers. I've looked through jnz but didn't find it or I'm not looking right. Thanks.
Hey guys I was wondering if anyone knew a decent priced paint shop or if a member has experience with painting cars? I don't want to spend too much but I don't want it to peel in 2 years.
Hey guys/girls, I have to get emissions done in a couple of weeks here and was wondering if I'll pass without a cat and with the wideband 02 in the rear?
Don't know if anyone is interested but we're having Smoochknob at Refectory! If you don't know who they are I provided a link. I believe it's a $5 cover but I may be able to get some people in for free.http://www.smoochknob.com/
Searched, hoped it was boost leak, but I think it's my spec 3+ 6 puck clutch slipping after 650 miles of breaking in :notgood:. First 5th gear pull from 65 to 80, will hit 17 psi and the clutch seems to start slipping rpms shoot up, holds boost but feels slow until it grabs again near 6k -...
First time using dsmlink and wideband, kinda scared, at idle my wideband is anywhere from 15 to 17. I didn't let it warm up all the way because I was scared. Please help!Mods:
fp t28
fp2 cams
intake with stock maf
stock 450's
stock pumpI zeroed out timing and fuel. Maf comp. at...
Looking to pick up a 95 GS-T with a 20G and what the guy thinks a broken rod, he said its knocking because he threw on the 20G with no supporting mods. I was wondering what I can expect to get out of it if I bought it and parted it out. I will probably keep the 20G though. Thanks.What I...
Hey guys, just got done doing a couple of pulls and logging with evoscan. How do things look? I have a wideband but haven't installed it yet. Also I have dsmlink but haven't installed it yet. Bought it used and don't know how to use it yet. Trying to keep it as "stock" as possible while breaking...
Hey guys, Finally got my car running after a year of slacking off. Anyway, been having many issues, first the starter wouldn't engage, fixed that. Then on the first 4 miles my power steering pulley came off :( Anyway just replaced the belt and downloaded evoscan. Got a cable for dsmlink but I...
Hey guys, I searched and found this picture. Anyone know what part number or thread size this is? Thank you.
<left>
<a href="http://s265.photobucket.com/albums/ii229/nsaechao85/?action=view¤t=img0005tf3.jpg" target="_blank"><img...
Hey guys, I've been reading/searching on this for a week now and no definite answers yet. Here is what I do know, awd starter plate hacked to make it work, I am getting a fwd starter plate on Tuesday (I was the moron who ordered the wrong starter plate and installed it =(. I had my starter...
Hey guys I just got my motor back and I'm going to be dropping it in tomorrow. I was wondering about breaking it in. I have 880's injectors, fp2 cams, and t28. Tuning with link and wideband. I'm just curious how I'm gonna tune without breaking it in. Should I find some 450's and just monitor for...
Well I finally got my head off and I did not like what I saw. How bad does this look guys?I'm unsure how difficult it is to do a head job as this is my first rebuild ever. Any suggestions? I've got the DSM CD and a Chilton's but I have a $1000 budget for the rebuild. I do however have all the...
Hey guys its my first rebuild on any kind of car and I've got the motor and tranny out. I'm a little stuck on taking the timing belt off. I've been told by a friend to mark where all my timing marks are, but if I'm rebuilding and getting the block hot tanked and what not, can't I just pull the...
Well the motor is at English racing now, awaiting for them to come back from englishtown. I think the route I'm going with is sticking with my FP BT28 and try to max it out. I want to stick with the T28 so it looks stock under the hood.Parts will hopefully be:refreshed bottom end (new rings...
Got this from another forum. It could affect us all!SEMA SAN - SEMA ACTION NETWORK"prohibit the sale and distribution of aftermarket motor vehicle parts if alternatives are available that decrease greenhouse gas emissions from motor vehicles.Spread the word! If you can Vote, you...
Well I just got done with my compression test and it went like this:
~180 ~180 ~130 ~180Then went back and did a wet test on the third one and the compression was ~210, now correct me if I am wrong but the test suggests a worn o-ring. Should my next test be a leak down test? Someone suggest...
Hey guys trying to solve this problem, I run out of fuel and run super lean at 16psi. Mods are FP BT28, evo 560's, evo fuel pump (not rewired) and STM's fuel kit (pump to rail). I was told before I did the STM kit that it was probably my fuel filter, so I got that done and I'm still running out...
Need help again. Just installed STM fuel kit (pump to rail). My old filter was clogged and brown gas came out of it, with things that looked like a hair ball. I am backfiring at idle lol. I think I'm running rich here, but no logger and no wideband (I know I'm retarded, but I'm poor). I used...
Alright I've cut the damn line twice now and it keeps fraying up and I am frustrated! I'm using a dremel with a cut off disc on high speed. Taped the crap out of the ss line and proceed to cut it slowly. Any advice on how to not make it fray? getting really irritated. Please help me!:cry:ps...
Need help on initial settings to drive to the tuning shop.I have fp t28 560cc injectors and evo fuel pump. Thanks.Sorry I don't have a logger right now, I'm using the one at the shop. Mods are FP BT28, injen intake, evo 560cc injectors, evo fuel pump (not rewired) and greddy fmic. I've went of...
:confused:Sorry I am dumb, also I don't have a jack right now. My question is, is this the stock exhaust system? Sorry for the horrible pictures! I know it is a dumb question but I am dumb<center>
<a href="http://i265.photobucket.com/albums/ii229/nsaechao85/P1012770_resize.jpg"...
Okay...after I took out the turbo I found out it was the old fp t28/28 turbo, 10 exhaust wheel blades. I am installing an FP big t28 9 blades. I've been running the car for a year now and it didn't have an AFC. Been running fine a little rich but could it be that the previous owner got it...
Hey guys, question is will the FP dsm gasket set with the oil supply line be all I need for the install? Maybe turbo oil drain gasket? Do I need any banjo bolts or anything else? Also I'll be getting a manifold to head gasket. I also have an evo III O2 housing.Gasket set
Forced Performance...
I'm getting my FP big28 in a week along with evo 560's and evo fuel pump. I already have an SAFC and FMIC. I am wanting to run meth/water injection. My only concern is would I be able to tune the meth/water injection with the SAFC?