What ignition system are you guys having success with the. Buschur cop, I know I know the stock it better I get it. But the cop looks very clean and I want to make it work. Arc-2? I understand the wasted spark system we use just want to see what you guys have had success with. I’m running link...
Do we have supportting vendor who sales rota/slicks? I’ve tried the Facebook marketplace and on here for used without any luck. Who has had luck buying from a business?
Just picked up a auto conversion, I would like to have someone build the trans/stall before I swap. Any recommendations? I don’t have Facebook and it seems difficult finding someone. Thanks!
Wife and I drove about 2 hours to cars and coffee then was heading home ( got gas ) when the car just died like it was out of fuel....It'll crank up for a moment then die. If it sits for a while it'll crank and run for a few min then die..trailered it home, Replaced fuel lines, and new fuel...
Which is best here? I have a perfectly good stage 1 shep trans but I feel like I’m on borrowed time. I’d like to go ahead and change now. Who’s does dogbox’s anymore since I think shep is done? How hard is a auto swap? Thanks guys!!Build list.
Block:
Decked to match head
Bored/Honed – .02...
Anyone ever done this? The only differance is the 7 bolt bearings are 100 thousands narrower. My machine shop said it would help reduce fricton and should work. Has anyone done this?
I bouhgt a chip from dsmchips and im not sure im putting it in right. Has anyone installed one before? I matched the groves up and I had to bend the tads a little but after pushing it a=down there is still a little gap between the bottom of the chip and the socket. It feels like it is far as it...
My car is currently not set up on blow through on the gm maft. It is next to my air filter. So is it going to be a pain in the A to tune? I have Safc, maft translater, 750cc. afpr, rail, 255 rewired, street frount mnt, new 60-1 turbo, tail 38 wastgate, and greddy bov( resurculating). Or do you...
Has anyone ever had a problem using the topline oil pump for a 6 bolt? I heard the suck the pan dry but ive already got one about to go on and was wondering if anyone has had this problem.
Who knows were I can find a map of were all my vaccum hoses go? Im putting my engine back in (after new build) and cant remember were all these vaccum lines go. (im from Alabama). So thats why.
I have a 1991 gsx eclipse. Its my first dsm. i bought it today. It has the following mods and bear with me if Im saying this wrong because once again this is my first dsm and turbo car im a former mustang guy. A gm MAF 2. A 14b turbo. A big FMIC. A maf Translator?. A turbo timer and electric...
What do i need. Im rebuilding the internals ( piston,rings,crank and rods ) so what do you think i need to buy? I have Bushur fmic, 61 trim t3, 660s, afc , gm maft, 255 fp, and 2k to spend on the rebuild. Do I need an anything else?
My dip stick blows out when I hold 15 psi or over to 7k rpm. No smoke. no noise. 130,000miles on car. what is wrong. rings? piston? or pcv valve and where the hell is the pcv valve???my mods are as this ....HKS 2.5 exhaust (no cat) SPI Boost Gauge Cyberdyne A/F Gauge Blitz Dual SBC (Boost...
I have a gm maf and translator and someone told me to zero it out until i find this boost leak i have. Also I ordered a new 255 walbro fp and what does it mean to rewire it?
I have a 91 talon tsi awd and my mods are HKS 2.5 exhaust (no cat) SPI Boost Gauge Cyberdyne A/F Gauge Blitz Dual SBC (Boost Controller) Blitz Dual Turbo Timer MAFT (can be used to tune much like the AFC) 3.5 GM MAF Front mount intercooler w/ all hard intercooler pipes 3 inch intake pipe with...
I ran 15psi a blew out my fitting that goes from the fmic piping to the maf its a 3in to 2in rubber fitting? and also the one on the turbo to the intake filter. were do you buy these and which ones are the best?