I am looking for some support. I either need together information on everything needed to flash and log my 1999 gsx using the current Black Box Ecu or find someone to flash a tune in it for me. Can anyone help me out there?
Can anyone tell me where to locate the pin on the ecu for the knock sensor on a 2g dsm. I am super frustrated.
I keep seeing 95-96 on pin 78. What about 97-99? Does it work different?
I need to know if I can temporarily use my back up 16g using a tdo5 turbine wheel into to my turbine housing that has been bored out for the tdo6sl2 wheel? I am ordering new wheels for the 20g that was on the car. I know the whole is larger but will it hurt my back up 16 g?
Hello Everyone,I just wanted to stop by and tell you all I have a chance to race against Farm Truck and Azn coming soon.
The car has to be a true street legal car with no roll cage. Has to run e85/pump gas or diesel.
Has to run full interior and exhaust no full cell is allowed either. This...
I have two good GM Mafs. $35.00 each.I also have the 1G ECM Tuning Cable that Converts GM MAF plug straight to the 1G Factory Plug. For use with Ecm Link V3, This cable cost $85.00 dollars new. I will take $35.00 for it.One Maf is sold. I have one left.
Text 812-821-8700 I only accept PayPal
Is there away to make my methanol tank shut off while my clutch is pushed to the floor?
While I'm trying to launch it kicks on and floods out the car while revving. I want to momentarily disable it. I'm looking for ideas using the clutch switch. I really don't want to flip a switch.
I just wanted to get some thoughts on a turbo I am having built. As far as possible hp and street manners.I am having an Evo 316g machined to accept the extended tip billet 7 blade 20g wheel. I am going to use the 9 blade tdo6sl2 turbine shaft and keep it in a 7cm turbine housing that has...
I have a mystery I need help solving. I have an automatic AWD transmission and it has no numbers scribed into the vin plate on the bell housing. I was able to locate the number W4A33 EV-S on the bottom of the bell housing. I called John at IPT tuning and he said he has never heard of this...
Hello,I just bought my first 2gen eclipse gsx auto. Here is the issue. The car will only go in reverse with the TCU plugged in.
But when I put into drive it has no other gears they just free rev like it's in neutral. If I unhook the TCU, I then can move the car forward but I have drive and...
All right I been reading. I read that an open o2 dump will not increase power just noise. But , I have one question. What if you have a 2.5-inch turbo down pipe and you're running 25 psi? Wouldn't the 1.5 open dump pipe help flow and increase the power capability? If you add the 2.5 plus the...
So i took my dsm to my local drag strip in the country. Nobody really cared for this car and wouldn't even line up to race. So i figured if i made this cool 350 chevy hood decal i could fool them into thinking it's a Chevy Swap. Now i might just make a friend. Or maybe i will just buy them all...
Can someone help me out here. I need some photos along with the width and height of the rear right decals found on the bumper of the eclipse gsx and non turbo models GS. I could use the width and height of those decals also. The photo or photo's need to be perfectly horizontal. On the gsx i...
Ok I bought new head studs. I'm changing out my head gasket going back to MLS my head has been all resurfaced and my bock is good. So here is my issue. I do not have moly lube or the awesome arp lube.I was reading I can use 10w30. But the torque specs are higher. I looked everywhere I could...
I need to know if the front spindle and knuckle from a fwd turbo or non turbo will fit an Awd
Model. Specifically front drivers side. If you could enlighten me thanks.
Ok im replacing my cv axle. The axle is not in and the rotor is quite seized on by rust. But i noticed it wobbles a lot. See the attached video. I Guess i will locate a puller for the rotor to remove it.
Well i went ahead and picked up one of the FP 68hta turbos. I currently run 550cc RC injectors. I also run a 390 cc methanol injector from my trunk mounted kit. How much injector will i need to max out this turbo? Keep in mind i use a safc. That's all i got for now. Although i may purchase down...
I need help with picking out a wide band O2 sensor for my setup.
I use the Tmo logger software. I need the best least expensive sensor I can buy
150-190 range. I need the gauge wires and sensor. Will this work with without a DSM link?
I can't seem to find a 1g DSM install page without DSM...
Just wanted to see people opinions on an idea i was thinking about. And if it's even possible?Can you make a evo3 turbo except a tdo6 variant turbine wheel by machineing the 7cm housing.
Could you squeeze more top end from the evo3 16g?
Like adding a 7cm housing to a 14b but increasing the...
Hello,My car starting making this noise after i shut the key off. I smelt a strange almost wire burning smell but found no bad wires. My car still runs and drives? What is it . What should i do or check out.Please see video!
Well i bought this MHI EVO 3 turbo cheap today. I was told it worked great and boosted great. But i noticed a few chips in the blades here and there and need some help deciding what to do next. Please look at my photo's.Compressor wheelTurbine wheel.
I recently had a spring crack in my act 2600 clutch. My pressure plate looks good. The clutch even looks good but i had a spring failure. I would like to replace the street disc. But i read some have had issues with the older style act 2600 pp. Forks hitting the springs i guess? The build date...
Hello,Can some one help me here. I need a compsite headgasket for a .060 over 1g
4g63? Where can i buy one? Will i need to buy a 2.4 headgasket? I think a .060 4g63 is equal to a 88mm. I need some good answers so i can get this fixed.Thanks.
I need some help. I need a headgasket. My motor has been bored .60 over before i bought this car. I would like to run a factory headgasket. Is it possible to get a factory headgasket .60 over and is this really 86.5 or 87mm?Can i use a cometic 2.4 4g64 or a stock factory 4g64...
I think i may have a bad bushing? I have no idea how to locate the part number or how hard these bushing are to replace. I will shoot a picture of the culprit. However, my right rear tire shifts forward and back while applying the emergency brake. So i jacked it up and was able to slide the tire...
I was wondering if adding a 6cm turbine housing to a 20g tdo5 would increase the spool time of my 20g. It may sound strange but i would just like to get more torque down low. It spools around 3800 rpm now. I was wondering if i would notice a huge horspower drop or maybe just a trade off of...
Hello,
I thought i would share some photo's with you all of my reflective stickers me and a coworker made for my dsm. Tell me what you think.I know i should have washed my car but check it out.Fender badge eagle emblem decal.Side vew blurry but you get the idea.
I seemed to be running very cold water temps. I was wondering if i install a factory thermostat if this will help my fuel mileage or not?Thanks for any information.
Can anyone tell me what font is used on the factory sticker for a 1g Eagle Talon?I am looking for the rear right sticker font and the Tsi sticker font.Thanks for any help.
I am trying to fix an issue? My problem is when i step on it in first gear it will only reach 17 psi. In second it jumps to 20 and in 3rd around 23? Im not sure why it's doing this and how to fix it? Does anybody out there have a suggestion?
Alright i bought me a 1991 5 speed awd drive. I jacked up the rear end and noticed it has a jh1 4 bolt rear diff. This part number is for an auto. So i noticed it looked like someone had been in this rear end so i took off the rear cover and did a ring count. I came up with 39 on the ring gear...
Are 4 bolt axles the same in auto and manual?I bought a 5 speed awd. I jacked up the rear of the car and lone and behold it has a 4 bolt automatic rearend? Can i just swicth out the chunck and keep the axles? Will a 4 bolt manual rear end chunk swap in or will i need to buy the whole thing...
Is there anyway to increase the oil pressure in the head of a 1g 6 bolt motor? My motor does have its balance shafts. It just seems i have low oil pressure in the head. I thought there was a spring or something that could be modified? Any suggestion would be greatly appreciated.
Hello, I recently bought an eprom ecu from MOTO GUYS GARAGE.
My issue is that no matter how high i crank the boost i get no knock whats so ever?
So i swapped in another eprom ecu ,used the very same chip and i was getting knock then maxing out at 43 counts buy 20 psi? So is my MOTO GUYS GARAGE...
I am getting a 1g 5 speed awd that has a unfinished holset hx35 setup. Does anyone have any suggestions where i could find an intercooler piping kit to bolt it up to the front mount? Or do i need a custom build. It will be a short route kit.
Thanks for any help.
Hello i have a key driver chip with Nlts and adjustable rev limits. If i do not get the clutch wire hooked up right could it cause me to hit a rev limit, if the ecu doesn't know where the clutch is. In or out? Because my car is cutting out at 5500 rpm? This is a 5 spd car not my 1g auto, Thanks...
I was wanting to find information on 4g63 swaps. I am most interested in older rwd conversions. Like the mistubishi sapparro 1978-1982 or Dodge challanger or dodge colt from the 70s up. I'm looking for light weight rwd cars. I would like to no about trannies that will bolt up and motor mounts...
Okay when you go +10 Is this adding more fuel and timing over the base ecu maps? Or is -15 adding more fuel and timing over the ecu base maps?My car seems to run the best fully maxed out To +50? Does this mean i need bigger injectors? Please help.
I have a question i was contemplating and i need help answering it? I was wondering if you could tune an eprom ecu to link into the brake on an automatic. much like anti lag or nlts mod. The reason is so when your at the staging light trying to build boost you could have the timing maps retarded...
Is there anyone out there that has torque converter bolts for a 1g auto? I am stuck and have not been able to find some. I will post in classifieds but i figure auto guys generally are not looking for folks needing these bolts. They are short bolts and bolt the flex plate directly to the torque...
Im looking for some flex plate bolts that bolt the torque converter to the flexplate for a 1g . Does anyone have any? Or is there is a place i can get new ones. I'm not sure i can get those from the dealer? Any help will be greatly appreciated.
What do you think about using a 100 psi fuel pump in a water injection kit? Is it ok to drop a fuel pump in pure methanol? I have a cooling mist injection kit already it is before the throttle body. I am wanting to inject pure methanol only at the track pre turbo using methanol i heard helps...
What is the lph on a stock 1g fuel pump? I have a extra stock 5 speed turbo fuel pump and my friend has a stock 240sx with a turbo and he is only wanting to run about 12 psi on his car i was wondering if my stock fuel pump would be enough for his car all stock using a t/3/t4 turbo running 12 psi...
I could not find the proper forum to place this question in so i put it here for now.My question is. Is the 6 bolt 1g turbo starter different from a 1g 7 bolt starter? This gets really confusing because they put 6 bolt motors in early 1992 then mid year switched to seven bolt cranks? I need...
Has anyone out there ever tried a spacer 1 inch to 2 inches thick between the stock 1g manifold and head to see if it would add torque? I wanna no what you all think? Please let me know? I see intakes like the frh/fhr racing intake using them and other smim but what happens when you use that...