Hi, a few days ago I noticed that my car started to push coolant into the overflow reservoir, so I did some tests and heres what I found:No oil in coolant
No coolant in oil
Compression is perfect
Cant see any smoke when drivingOnly seems like it's pushing coolant under boost, also...
Hey there, after i installed front control arm and sway bar bushings my car's been understeering too much, so Ive decided to buy a rear sway bar along with rear suspension bushings. So I have 2 choices Suspension Techniques sway bar or RM sway bar, which in your opinion is better? After some...
I bought a used ACT flywheel off my friend that had the 6 bolts in it and 3 pins for the presure plate, but when i sent it to a machine shop to get resurfaced, they misplaced the 3 pins. Would stock pins also work? Or do I have to look for the right pins for the ACT flywheel? Any help and input...
Hi, if I just start cruising on the streets at about 2K RPM, my car starts bogging unless I give it more gas. And today I took the car out and punched it, 1st gear felt very weak and in 3rd gear at about 5k RPM car starts bogging. Right now I have at small boost leak on my TB shaft seals and...
Hey guys, yesterday I ripped my stock intake manifold off and I need to clean it up because it's all dirty. Well today I'm gonna take it to work and sandblast it. Is there any special coating to preserve the sandblasting look? Or what should I do?
Since I changed my UICP and cleaned my TB, my car has been running very bad. After I installed the UICP I tried the car on my street and it wasn't boosting at all, but later I found out that my MAF was disconnected. I haven't been driving the car and now it seems like I have another problem...
I bought an Air/fuel gauge by Autometer, but I can't figure out where the 02 sensor wire is..I looked on VFAQ where they explain where it is, but once i checked for resistance on that connector i was getting 2.5 ohms which is too high.. Would it be easier to tap it right into the 02 sensor...
I got an Autometer short sweep electric oil pressure gauge that I'm installing in my car right now. I have all the wires inside my car but i don't know where to connect them to, can anyone please help?
Well I just installed an Aeromotive AFPR with SS feed line and a regular rubber return line. Well after having lots of fuel leaking issues out of my return line clamps, I finally started the car with no fuel leaks, but now I can't adjust my pressure it always stays at 30 PSI. No matter how much...
I just changed my UICP and decided to go test the car out even though i was idling at 2k RPMs. Well once I started accelerating my stock boost gauge was at the negative mark the whole time and car was running slow. And when I parked it my RPMs kept jumpring from 2k to 1.5k. Could it be a bad...
Well, my car is running really rich(255 pump and 550 injectors) and i was checking out my fluids and my oil smelled like fuel and i started getting this squeking noise coming somewhere from the cams, so I decided to change my oil. I ended up overfilling the car with oil, but the car started and...
Well I soldered all the wires into the ECU Harness like the Instruction manual said, and I did it by Karman style. Well after I did everything and the SAFC2 doesnt power up at all, I even took it aprt and checked those little connectors but they are all there. I soldered the red power wire into...
Well I just bought a 1990 Talon Tsi AWD with a broken fuel gauge. I tested the sending unit with an ohm meter and it read 72 ohms which is about right, I have about half a tank right now. So what else could be the problem? The gauge itself?
Well yesterday I bought a 1990 Tsi AWD and the seller told me that the car was running very rich and if you stall its very hard to start it up. Well my friend took it for a test drive and stalled it, so we had to push it order to get it started. So then we started to head back home and my friend...