I took my rear subframe out for rust cleaning ,powder coating and bushing replacement. I took the old ones out using torch was an easy job. So couple days ago I received my new torque solution bushings. As I review the installation ,it says,that I need to keep the original center pin with...
I was looking for oem parts online and came across Mitsubishi Parts | OEM Mitsubishi Parts | Genuine Mitsubishi Parts. They have every part you can think of. hard to believe,but prices are good too. What you think guys is his website legit?
what you guys suggest me to go with oem or aftermarket bushings? Im building a comfortable and smooth dd. Will have ac,ps and other stuff. I'm trying to get as low vibration as possible.
Im trying to see who wants to trade tan interior to a black one. I got black leather seats with the rest of the black interior panels and stuff. I got myself a black 2g that i think tan color will flow much better then a black one. My black interior condition is 9.5'out of 10.
Will that help to absorbe road ,exhaust noises and vibration,and for music to be abit more cleaner? The reason why im doin this -to have quiet,smooth,comfortable ride....
I noticed that after rainy day my driver side floor mats front and rear are gettin wet. So a day after i saw a water run marks commin out of my speaker grill. So what it would cause this kind of a leak? weather stripping around the door is in a good condition. The only bad thing that i have-3 or...
As my heater core is out, i want to make AN fittings on heater core pipes,so i could use a ss braided lines from thermostat housing to heater core for making my engine bay nicer. The question thats bothering me is:Is it better to weld a brass AN fitting on the heater core pipes or just make a...
Well i already started to work on my winter project, repainted engine bay, sandblasted and epoxy painted front subframe waiting for a new bushings to come in.....
The next thingf what i need to do - get rid of the nasty smell of my interior and exterior:
The smell is comming out from the...
Ok i got a new winter project for myself as an early Christmas gift lol :))))The things im going to do with it is a complete restoration close to near stock look.
I already took both front and rear subframes out for clean the rusty surface ,epoxy paint and will replace old bushings to the...
I did a battery relocation to the trunk. I used 2 awg wire for positive (+) and same gauge for negative (-). The thing is,that when i crank the engine ,the positive wire getting hot and if ill crank car longer ,the fuse pops out. Should i use 0 AWG wire for positive and leave the negative...
Im in a marketin of a new driveshaft bearing. are 2g awd's using 2 carrier bearings?? Because i saw under the car only one,that is is in the middle under the car. So why places ,who selling these carrier bearings for 2g awd's are listing as a 2g awd front and rear drive shaft carrier...
I started having problems with the cal lately. It started to bog at low throttle.Its really hard to start,takes like good 10 secs..... After i shut off the engine,my Aeromotive AFPR not holding a pressure. The needle on a gauge goes to 0 within 5 seconds...... I got a 255 HP fuel pump...
I had a breather filter on my valve cover,theni decided to relocate it to not splash the oil in the enginebay. So i took a long hose ,routed down under the car and put a breather filter at the end of the hose. My question is:
Is it a good idea to use a pvc valve in line of the breather filter...
After a long thinking,i decided to part out my 1g fwd turbo dsm.As having limited storage for parts,i can't keep them,so i have to sell. The only thing,that i will be keeping for a build-Motor.
So transmission is in a good condition.last time when i was driving (a year and a half ago) it...
Today i went to the track ,was hopping to gert into 11's. But i was to far from 11's. My best time was 12.7. Here is the entire 1/4 mile log,any suggestions?!
Yesterday,i went to do a dyno pulls and i was a bit disappointed of the power my car made, First pull i made 237 whp (wtf???!!!) car i capable to run over 400 whp. So after some adjustments i reached 378whp,and that was the most i could get out of many pulls. here are two logs: Any...
After i dialed in my idle and cruise,i went to do a wot tuning. Did 4 pulls,made some huge adjustments,because my timing and afr tables were out of wack. So Here it is. I want you guys to suggest of what i could adjust more to get more power out of my car. BTW is it good to advance timing from...
i was looking at my log today while i was idling,My STFT are bouncing between +2/-2%. LTFT lo are sitting right at 12.5% and not moving at all,i tried to mess with global fuel and injector deadtime to see any changes in LTFT lo ,but nutting changed. Then i saw,that the LTFT mid are sitting at 0...
I tried to look for the wiring everywhere,but everyone has the diagrams about AEM UEGO . I got an AFX wideband o2 sensor located in a front o2 housing. I got two wires coming out :YELLOW- analog output signal wire. BROWN- analog output ground wire.Which wire i should connect to the ecu,and witch...
I Helped my friend to do a clutch job. The car was sitting almost three months. Today ,after we put everything back together,started the car and we heard loud noise coming out of the wastegate tube. So i took a car for a test drive ,and i was building only 7-9 psi to redline. (Gt 35r turbo). So...
Im having problems dialing in the airflow.I can't get the airflowperrev to .25gm/rev. Its just bouncing around instead of being steady ,and i need to lower the airflow so damn low,to get close to .25gm/rev. What could cause me this??? Injectors are dialed in using ecmlinkwiki.......
Hey fellas, I tried to adjust my tps volts ,so at idle i could see 0.63v and at wot 5v. So I rotated the tps,and the lowest i could go was 1,19v as of 19% of throttle. I couldnt rotate more,because the holes for a bolts on a tps wont let me turn more to make my voltage lower....... Where it...
A week ago my car started to bog,sputter on low throttle. When i give gas to 3k rpm's ,it feels like the car is running on 3 cyl. After i pass a 3k mark ,the problem disapears.And the rpms goes kinda slowly to 3k rpm mark.so far i did :
fixed boost leaks
changed wires/plugs (ngk gapped...
After setting my idle,cruise fuel trims ,i made a wot log. After i made a log, i looked at it and my afr was so damn rich. So i adjusted the numbers in "OpenLoopMaxOctane" DA. Went again for a wot. Wasn't happy with the afr again. so i made numbers higher to the point ,where it looks kinda weird...
I bought a Timken Rear wheel bearings/hub. Made round 6k miles,and the bearing are shot now wtf? Im trying to figure out,what could cause my bearings to go bad in such a short time? I found another two. one of them is Timken and NTP As you can see, its a big price different which...
I moved my AFX Wideband sensor from the rear o2 to the front o2. Tapped the 0.5v output to the ecu's pin #76. With the fuel trims seted where they supposed to be . Airflowperrev - .25gm/rev and Combft +/- 1% Question is with that fuel trim hat i got my wb supposed to read 14.7 :1 but it jumps...
hey fellas, ive been trying to adjust my ft for past couple of days,and i just can't get them to where they should be. I was following the demo on the ecmlink web,but i got no luck :(. would anybody give me any advices of what could be wrong,of adjusting the fuel trims?
Today i was trying to tune my car by adding timing. Before i was runing 17 deg. from 5300 to 7650 rpms. Today i added 5 more deg on top and didn't see any knock. Is it normal or something is wrong? im running 23psi, 93 octane+ 20% water and 80% methanol. would adding more timing will give me...
recently i upgraded my clutch system. Wole the parts are new:ACT 2600 pp
ACT 6 puck disk
oem tb
fork
pivot ball
slave/master cylinders
SS line from master to slave cyl
i tried every possible way to bleed the clutch,and i still can't get the air out of the system. There is...
i dis some tuning before the track,and i want some people who knows a lot bout that stuff to give me any suggestions on it.i mean does it look good? or what i should adjust to squeeze a bit more out of my whip.. because im tryig to hit 11's and be done for this year.... :D
i was tuning my car with an ecmlink today,and i noticed ,that my volts are dropping during wot pulls. i got an aftermarket gauge. while driving or idling ,the voltage is steady from 13.5 to 13.9. but when i do a wot pull it drops to 10 volts and bounces from 11.3 to 10 while im at wot. and the...
Im working on my friends 1g, after i put the motor back in,tried to crank,and the starter wont crank the engine. (new battery starter harness are good). It will start spin if ill help to turn by the hand (crank pulley) What is the prob???? can a starter get to weak to not crank the engine...
i got a SMIM and accufab mustang tb mounted on. Did a log with dsmlink and found out,that im getting a 28% on closed tps and 87at wot. ried playing around with tps adjustments (tps scale and tps offset) gouldnt get 0% on close tps or 100%at wot. Plus the TPS itself is not moving on a tb,it just...
I need to upgrade my IC and IC Pipes. The reasons are:The pipes,that i have now are 2inch diameter,(i think some cheap ebay pipes) came ,with the car ,that i bough last summer.
The intercooler core has a huge bent on a bottom(getting on a tow truck) and the Intercooler came with long...
Supp fellas. Today i received the letter,actually the bill,for my accident,that i had last summer. I spun on a road.due oil spilled.and there were total 4 cars,that had an accident in a same spot,at almost same time. So today I got the bill for 4k, of the road damage,which is not right i...
I had a leak through the freeze plug,which is under the intake manifold. I bought a rubber one,that comes with the nut in a middle.So i put that one in and after couple days it started to leak again.... My question is: If ill put the metal (OEM) in there,will it stop the leak?? Is there any...
well today i wanted to do an ignition timing,but when i took the upper timing belt cover,i saw,that my timing belt is shifted to the side (towards the strut) It was a good half inch off of the cam gears. So i took the rest of the timing cover off,and i saw, that my tensioner control arm is...
I got some dsms standing in my backyard and im runnin out of space ,so im trying to sell my 1g. The car doesn't have engine.It has a complete interior,tranny,3in custom turboback exhaust (with megan racing muffler).FMIC including pipes,has a gm maf translator GenII.Enkei 17" wheels.The car has a...
Well after i put the motor back on my 2g awd build,one thing is bothering me alot. How should i hide the wires ,which goes on top of intake manifold? (injector plugs,cas plug,coil plug etc.).I got 1g head on my 6bolt and i got no place to bolt down that plastic bracket for wires on top of the...
Im looking to buy a new Both rear wheel hub (complete setup). And i came up to the One,that Ebay has.Does it look right? because the price is really cheap.because i checked everywhere and they run over 300 a peace.....
2G GS-T tranny.In a great shape,shifts perfect.Took out from a running car. Asking 400$...FWD Clutch kit Brand new,the pressure plate is brand new,it still has a tag on it,and the clutch disk is new too. asking 250$ACT streetLite Flywheel 150$2g Head,that is made to work with a...