Which cooling fan would you get?
Don't know if amperage is too much or not.Derale Cooling Products 16925 - Derale Performance High Output Single RAD Fan and Shroud Kits - Overview - SummitRacing.comSize 12 push / Part# 2030 - The Fan ManThanks
I installed MAP and IAT sensors but cannot get either to log.
MAP blue wires is soldered into pin#16 (baro) on ecu.
IAT is wired to pin#24 and pin#8 on ecu.Do i need to splice them in to the ecu harness or just cut and solder?Thanks
So from what I have been reading FIC 850's are rated for 850 @ 43.5 psi and 776 @ 37.5 psi.
Since I have a 1g should I calculate my global setting for 776 and set my fpr at 37.5psi or 850 and set fpr to 43.5psi?
Does it make a difference either way?I am trying to match afratioest to...
I was having some issues with knock before even after pulling timing, so I wanted try some Sunoco Cam2 gas (100oct). Seems to have gotten rid of most of the knock.
Can I just run this gas from now on?
I might look at a meth injection kit next as well as a larger fmic.
Anything jump out from...
ok so i am trying to figure this link stuff out. Since I have a 1g I changed my timing sliders to the 2g settings.-Can I just use the DA timing tables from here on out?- Wherever I see knock, pull timing as long as afr's are ok?Thanks everyone!
OK so I am trying very hard to learn how to tune but I still dont get a few things.
So far I understand getting your idle and cruise setup. Its after that that I dont get.
I made a partial 3rd gear pull and got some knock. Is it better to add fuel using sliders or maxoct table?
How do I know...
I recently put in FIC 850's and now have new logs. I wanted to find some help at the Northeast DSM Meet but I arrived late and everyone was gone already.
I tried to do a 3rd gear pull but immediately got some knock. Also my logged afr's are about 5 points higher than the actual gauge.Any...
So all of a sudden I cant get link to connect to my mac book. my questions is if the green light on the usb cable should be on when i connect it to the laptop?
I cant remember when it goes on.thanks
anyone have any suggestions for these?
I know PTE rates their injectors differently and 550's would actually flow around 510-520?I used the injector calculator on ecmlink and entered 510cc, is this close?thanks
Hi guys,
after trying this a few weeks ago I found out I had a blown headgasket. Replaced everything and Im back.
Can you let me know how this looks? I understand idle settings for the most part but not really sure what to look for after that.Thanks
I cant get a steady idle. Checked ISC,tried adjusting BISS, nothing.
Also in closed loop, how come my O2 sensor doesnt cycle? Its a brand new sensor.
any thoughts would be greatly appreciated.thanks
To sum it all up, bought a used 1g, put it all back together, went to start for the first time today and nothing. I hear a click and that's all. I'm checking around the engine bay and notice this fuse. Can someone tell me or show me what this should look like? It doesn't look right.
Hey guys, dropped the oil pan today to replace since its all dented and leaking. I was checking the rods and there is the slightest amount of side to side play. Should there be absolutely no play?
Hi Guys,After being out of DSM's for the past 3 years I finally got another one. Its a 1990 Tsi. Its been a while and I don't remember how lines are suppose to run or where they go. Hopefully you guys can help. I tried labeling things to help.What is A?I think I had B plugged...
I am thinking of buying a tranny that has a 22 spline output shaft and mine uses a 23.What would be involved to switch a 22 spline tranny over to a 23?Thanks
I am contemplating assembling a shortblock myslef and was wondering if this write up covers basically the same for a DSM. I want to learn how rather than pay someone and never have a clue as to how it is done. So far I have removed the engine twice,turbo install,head rebuild,etc.How many of...
I just got my car running but when I turn it off the SAFC stays on. I am going to check the wiring but is there any way I could wire the power to a switched power wire instead?
Heres the scoop. I removed the engine from the vehicle to replace valve stem seals,replace gaskets,remove balance shafts, new timing belt components.etc.
I finally finished putting it in last night and now I have no oil pressure.I primed the car 5 times for 5 seconds each time. At first it...
This is my first time ever talking an engine out of a car. The experience has been very rewarding so far. Thanks to this site for answering any questions that I had so far.I took out the engine 8 months ago to due to the following:
-replace valve stem seals
-new timing...
I have read how hard it is to remove the fuel pump nuts so I tried a new set of wrenches instead of flare wrenches.http://www.sears.com/sr/javasr/product.do?cat=Hand+Tools%2C+General+Purpose&pid=00942513000&vertical=TOOL&subcat=Wrenches&BV_UseBVCookie=YesThese are the best wrenches ever...
I purchased a 6bolt motor for my car and while I was cleaning it I noticed a broken manifold stud in the head. So I decided to take the head off and install a balance shaft elimination kit while was at it. After pulling the head I noticed coolant on the#1 piston and discovered it had a blown...
I am swapping a 90 6 bolt into my 93. The 6 bolt has no p/s pump but my 93 does. Would I be able to transfer the brackets and pullies over to the 6 bolt or should I run it without the p/s?
Thanks
I need to replace my valve stem seals. Would this tool do the job? any info would be appreciated.
Thankshttp://www.eppys.com/Shop/Product.cfm?OrderNumber=102304280502&Item=KD2078&CategoryID=23&SubCategoryID=12
I just received a 16 g I bought from ebay but it did not come with the turbine housing. Would the 14b housing fit or should I try and return this to the seller?
Thanks
I just bought a 93 Talon and the end of the pcv valve hose is not hooked up to anything. Can someone show me or tell me where it hooks into? I thought it went into the intake but I don't see a place for it.Thanks