Probably not tight enough. Remove the actuator bracket, or try to modify a socket or crows foot or something. Thread sealant isn't gonna do anything as it doesn't seal at the threads. Same goes for AN fittings - never understood people use teflon tape on the threads. When in doubt, ditch the...
That was the main reason for wanting it. Nobody was using one on a DSM, and the flow per wheel size is insane. It's basically the latest gen 3071 and it does 70+ lb/min. My goal was to retain or even improve the response from the current HTA76 in the FP30 bolt-on hotside while gaining 100-150...
The old HTA76 is hanging in there lol. I ended up swapping gates and put all the springs in, now it holds like 39psi to redline and it's night and day vs before. The 10+ year old tires are a little sketchy so I've got some new R888Rs ready to swap on. If I do the G30, then I'd be out of fuel...
Definitely not the case for me. I've got an EVO 6 and a Callaway Twin Turbo C4 Vette that sit as well. I just always gravitate to the newer cars, and if I want to drive something old I usually take the '67 Vette. Rad era for me is neat to have but too old to feel modern and too new to feel...
I'm in the same boat. I think I had my G30-770 before you got your new turbo and I still haven't gotten around to installing it. The car is absolutely perfect as a street/strip machine. Light, reliable, stupid fast, great spooling, handles and brakes well. But I rarely drive it. I put power...
Yes and no. 35R comp wheel. T04S comp cover. T3 stage III 76 trim T31 turbine wheel. BB center but not the garrett 35R type. Bolt-on hotside that they claim is .63AR but flows more like a 7cm.
As stated above, a 255/40 on a 17 x 9 +35 to 45 is about the most you'd want to run on a 1G. I've got 17x8 +48 wheels with 245/40s that fit great on my car.
On race gas, that extra timing really woke these cars up back in the day. We ran 11.0 @ 126 on a VPC, 550s, 20g, 272s, and no wideband. Stock 1G 7 bolt, head and intake manifold. Just plain old C16, leaned out, and 25+ degrees of timing at 30 psi. On pump, different story. You're not running...
They cancel out because you're telling the ECU that it's seeing less airflow, which makes it deliver less fuel. The bigger injectors cancel this by flowing more at the same duty cycle. The side effect, however, is that now the ECU is on a lower load table with more timing. May be a good thing on...
It's still together, the drivetrain is going into my friend's car but he's not the type to make much progress so I may dig it out again. I'd guesstimate it at around 2100 lbs without me. I'd love to get into tubular subframes, CF body parts, etc to get the weight down more but I don't have the...
Watch the video, he does some things the hard way but it answers everything. Rears are easier than fronts, you don't need to press the bearings out, they just tap right out.
Yes, if you unbolt the nut that holds the axle cup on, you can just tap the axles out pretty easily. I disassembled to do all urethane bushings and toe elim (you can see both in the pic).
You don't need to remove the hubs/bearings to get the axles out of the rear of a 1G. There are 3 or 4 bolt axle cups, you just unbolt the axle flange from the cup flange.
The car actually made 479/443 that day and would've easily cracked 500whp if I had more time ( it wasn't a tuning session, just a 3 pulls for fun dyno day). If anyone remembers Wendy's FWD build (Girlieracr4G63), she had an S258 bolt-on with a built engine and made 545 whp.
Definitely not a 3065, which used the GT3582R comp wheel. You can identify those by the hex nut shaped casting at the inducer side of the wheel. It's not anything HTA/HTZ because they're 7 blade and you can easily tell the difference between billet wheels and cast. This also has a .60AR hotside...
Yes, if you have factory dual piston calipers you just need the brackets and rotors. Less prone to warp, less fade with repeated stops, and the rotor design is different so they're negligibly heavier than stock rotors.
Sorry, thought since you had 2G wheels it was a 2G car. Yes, for an early 1G, you'll want any 92.5-up AWD brake caliper which will bolt right onto the outlander bracket. Ideally you want to stay with 1G calipers as the 2G and non-DSM ones have different attachments for the lines (inverted flare...
Is your car AWD? If so, you use your existing calipers and just change the brackets. I run the Outlander brakes with my 15" slicks and they clear, and they'll clear some of the OEM 16" wheels with plenty of room, but it depends on the spoke design, width, offset, etc.
They're VERY close but do clear on 1GA Talon wheels. You should be ok, but may want to get one bracket and try it out first (assuming you already have 2 piston calipers).
I ran a couple different ones on my old car. First was an OEM Syclone IC that I had modified. 5 gallon fuel cell in the trunk, OEM Ford Lightning pump and heat exchanger. Worked ok at lower power, but I ended up changing to a Bell core which worked great. No blocking the radiator, can keep AC...
Definitely not. They're casting their own. Cap, AN ports, area where the bolt holes are... Nice step between a stocker and the FF billet option. If they offered it without the logo it'd be way more appealing though.
Finally ran the car today. First pass off the trailer, went 10.94 @ 127. New personal best ET and MPH, first time running 10s. Set the 14b AWD MPH record. they hot lapped us and on the burnout before the 2nd pass it popped a coolant line, parked it for the day. May try to get it back out before...
Finally ran the car today. First pass off the trailer, went 10.94 @ 127. New personal best ET and MPH, first time running 10s. Set the 14b AWD ET and MPH record. they hot lapped us and on the burnout before the 2nd pass it popped a coolant line, parked it for the day. May try to get it back out...
They're out there and well worth waiting for over this one. There have been several that popped up recently. Here are a couple (still not 100% original but easier to put back to correct)...
Aftermarket sunroof kills it, not to mention the repaint wasn't done correctly - wing should be matte black. A true DSMer who wants one to collect would hold out for a more original car.
If it's really JB and an 82HTZ, it's a Black (and nothing like a 16g other than they're bolt bolt-ons using MHI bearing housings)http://www.forcedperformance.net/fp-black-for-dsm.html
The allure of a car has for decades been "sexy" curves/lines, flashy paint (makeup), etc. Not unreasonable for the stereotypical male to be "attracted" to his car, always the running joke that a guy loves his car more than his gf/wife, spends more time and money on "her", she'd never cheat or...
Agreed. My first car was a '93 AWD Talon 5spd, tan leather, no sunroof. When I got it, there were still plenty of nice ones around, but by '07 I was frequently told it was the cleanest DSM they'd ever seen by locals. I always refused to gut the car or do a cage, it was always a street car. I...
I was into V8s in the 90s, had a few Mustangs. A friend was into GNs and he eventually got a Typhoon which turned me on to the potential of an AWD launch and turbo power. I'd always liked the 1GB Talon looks, more classy and sporty than the typical Honda/Sentra SE-R econobox look. And the...
You don't need a block-off or bypass plate. You can pop the freeze plug out and turn the FIAV in until it's closed, then re-install the freeze plug with some fast dry/hard set sealant.