this is the kind of help I need! :thumb:in this case, what springs should I buy?
according to the link you put, they do not recommend these cams for turbos less than 67mm, but I am using a GT3540R, there will be problems?Thanks for your time bro!
Hey. I want to apologize because my English is not good, I'm using the google translator. I'm sure the head has not been milled. The pistons are JE and YES they have the relifes valves. The part number of the springs is "Manley 26115"
Here in Peru we can not measure the pressure of the...
Hey. Thanks for your replies, I appreciate your help.Neither the head nor the block have been milled. Pistons are 8.5:1 JE at 0.50.
Valves are stock, not oversized. Head gasket is Cometic, 0.045 thickness. The pistons are not machined valve releifs, just that's what I know, if required to...
Hi, I have a couple of questions about the installation of camshafts in a 2.0L engine. The camshafts are GSC S3 280/280 and have 11.7 lift, is this dangerous as the pistons can hit the valves? You need to do some work on the pistons? I'm using double springs Manley. I know I must be very careful...
I was running stroker 2.3 before this. Had so many trouble. Now i get this low mileage engine and im building 2.0L engine what i know very well.Stroker i was using had manley oversized valves but we didnt look instalation height and now that engine is broke.Im planning oversized valves...
hello guys.im building a new engine. eagle h beams and ross 8.5 pistons. stock crank.
got arps main and head and cometic head gasket.
head got manley double springs, titanium retainers and those big gsc s3 cams.
turbo is a gt3586hta, fmic , full race smim.car is full drag. transmision...
I got ring and pinion from summit (summit brand) and mini spool form summit too.Ring and pinion here: Summit SUM-740801 - Summit Racing Street & Strip® Ring and Pinion Sets - summitracing.comSpool here: Strange Engineering D1620 - Strange Mini-Spools - summitracing.comAxles are...
Car was running on C16 but very poor tuning due to test new transmision, new driveshaft and coilovers. We will visit dyno soon to make some tuning stuff.Gears are 3.55 (39/11), just same as center differential.
I want to use n2o only if it a MUST to spool those turbos, not to go faster.Are gt4094r capable to spool up without n2o? you know, for drag launchThanks
HelloMy car is 1990 talon tsi awd, it run mid 10s on gt3082r at 30 psi. I want to run consistent 9s , like mid 9s. Im between two turbos, gt4088 non-bb and gt4094r bb, first one price is US$ 1000 and second one is US$ 1500.
Question is, is it worth to spend us$ 500 to get ball bearing...
our system only reads reaction time et and tt. heh soo yea cant really tell ya that, and peruvian import laws doesnt let me bring used autoparts into the country so buying a used 4 bolt is close to impossible.
I cant express how much your comments have been a help to me bro, really, yea im def thinking of geting the gt4094r, the "strip" we race on is a slightly abandoned dusty cesna runway, but eh its that or nothing, the only problem right now with my car is the drivetrain ive already broken 1 of the...
Its a full race car no interiors fuel cell huge anoying aeromotive fuel pump fiberglass hood and other stuff, i want easy 9's, but with the gt42 r and standard displacement wont i loose time with all the lag it produces
Hi ima Peruvian Dsm owner, im runing 10.42 et's with an fp3082 forged with Ross pistons eagle rods, i have a magnus intake, hks 272 cams, my cyl head is also ported polished, my block is blueprinted and balanced, im at stock displacement, reving 9500 rpms, i just sold the fp3082 to my friend who...
Hi, gt3082 has garrett turbine housing, 3065 has mitsu turbine housing, they say 3082 have more top end and slightly more power capacity.Darkstartsi said FP3582HTA, aparently is an comon 3582 evolutioned, look this...
Thanks for inputThis was on race gas (in Perù 110 octane).Can i run some more timming? how much timing can i run on vp c-16 raceHow much psi can i run on this gt3082? is 30psi limit on this one?
(think so because small turbine wheel)Thanks for comments and helpingDSM POWER...
Hi folksGot a new personal record and new national record here in Peru. Total time 10.62 sec, elapsed time 10.48.Turbo is GT3082R, there was no nitrous used, the boost was at 30psi, AFR was around 11.1:1, timing maxed about at 18 degrees.Here is a video...
How much did you pay for?
Have you noted your "centerforce dual friction clutch" is in fact an Exedy-Daikin clutch?OMG
If you see that cover and disc, both of them have "DK" brand stamped on it.:shhh:
I think there is no reason to buy a "centerforce" or "act" clutch, when those are Exedy...
I recomend Exedy-Daikin stage II clutch. Kit includes aligment tool.
Mi talon runs low 11s and clutch doenst slip never.
Get cromoly flywheel too, its amazing flywheel.
Dont forget Exedy-Daikin make OEM clutches for our DSM cars, and EVO and STi also.
Good luck
hi, my GT3076R had very bad problem, it was FOD (foreign object damage), and i bougth 65 lb/min sold by forcedperformance. Problem is i cant get 0.70 compresor housing and i had to do some work to 0.60 a/r housing to stuff in this big compresor wheel.Please someone tell me, is there any...
Hi, my setup is Walbro 255 high pressure, 850cc injectors, stock rail, stock lines, aeromotive FPR.
Fully built motor (roos 8.5, eagle rods, all arp, hks272/272, exedy stage 2 clutch)
Car is making lows 11s at 23psi and very poor tune, but at this boost injectors duty cycle is at 98% at 9000...
I recently get some VP110 race gas from NASCAR.
What can i expect about this race gas?
Before this i was runnin 100LL light plane gas. (here in Peru this is the only gas we can get to go to track to race)
Thanks for adviceDSM POWER PERU
Hello guysIm running Haltech ECU, car is making amazing power, but i need your opinion people.
Numbers:
11.6 a/f
13 degrees ignition advance from 4K to 8K
25 psi boost on GT30R
110 octane gas
Mod list on profile.
Please, i want to know how do you look this numbers. Are they ok? Should...
Im getting SMIM from Magnus, ive researched about it and its looks very good mod, but i dont know if should i get big throtle too... :confused:Is a throtle a must with SMIM or can i leave stock 60mm on it?BTW my 1/4 mile time is 12.17 (mods on profile)What gains can i expect just...
Today i turn up boost to 23psi.
No more creep. :thumb:
Car holds 23psi all the way to 8K.
You people were rigth. GT30R likes lot of boost.
Injectors duty cycle was at 90%
Im thinkin to order 850 set to put 30psi on it!!
Sunday i will go to track, i hope to enter on elevens territory...
at 15psi is the same thing, boost creep to 20 psi.
Maybe i need a bigger wastegate?
In case yes, which one? 40mm?
my goal is 10s and 30psi boost
thanks for advice