hi there
sorry for the ridiculos long log tried to clip the section but it didnt work
i have a knock count of 15
from 338,100 till 338,220 on the time scale
is this actual knock?thanks
hi there
need some help with log seems that the omni4 bar is not responding aswell as some other valuesthanks in advance1G 1990 gst
2,3 stroker
borg warner 256 ET
s/m intake race throtlebody no biss/isc
speed density
bpr 8es
Hi there
After replacing copper headgasket for a mls oem headgasket engine is stil pushing coolant
This is one a new engine and new head mls torqued to 90ft/lbs
Engine did not overheat before so i didnt resurfaced the head
Because everything was new and the car didnt Drove much 10 Miles tops...
hi there
after a new starter
new starterrelay and new starterswitch still no crank
when turning the key i have 12 volts on the starter solenoid
but no crank just clicks
also the mpi relay under the radio clicks when cranking is this normall?thnx
Hi there
Look at the pic and tell me if this is the starter relay (Please)
Put in a new starter but it doesnt turn Just clicks
When i turn the key and hold my fingeren on the relay i can feel it clicking how do i take the relay out?thanks
hi
after doing a timing belt job timing seems to be off
i installed the timing belt aligned the crank sprocket on the mark and camgears with dowelpins up
i turned the crank 6 times and the allignment was still good
after installing the harmonic balancer (fluid damper)
i noticed that when i...
hi there
just installed a new oem mls headgasket
with arp L19 headstuds i am planning to run about 30 psi boost
i torqued them to 90ft/lbs
am i oke or do i have to torque them to a higher value?thanks
hi there
look at the pics of timing marks can not adjust this
its less than a thoot i think
when cam gears are alligned timing mark is past tdc and vice versathanks in advance
hi
i am running a race throttlebody with no biss no isc
cant get the engine to idle
unless i lock throttleplate at 5% is there a way to adjust this in ecm link?
i set the idle at various values in link but engine dont respondany ideas?thnx
after installing ecmlink car wont start (1G 1990)
was running fine before
installed ecm link and, sd connection with ecu was oke
fuelpump does not come on
what did i miss??thanks in advance
hi there need some input on 1000hp build (streetcar on pumpgas ?)
what kind of turbo/wastegate?
in/ex mannifold /throttle body?
clutch/flywheel ?
fuelpump? (mech/electrical)
injectorsize?
basicly all the bolt onsthanks in advance
hi there
this engine comes out of a 1994 gsx (7bolt)
the previous owner had it repaird
they put in a new set of pistons and rods the mechanic said the car idled for 10 sec started reving on its own and exploded (strange)
if you look at the pics piston 1&2 are oke but 3&4 are ruined including the...
hi there
can someone tell me wich connector i have to ground to set base timing?
i found a thread that said a yellow with red wire
my harness has two connectors
one is a black wire with white stripe (closest to the battery)
the other is a white wire with black stripe (closest to center of the...
hi guys
need some help to id a connector thats just above the fuel filter
it has 3 green wires comming out and a black one
its been about 10 years that i worked on the car
cannot remember what this was for
see pics
thnx
hi there
i have a BW 256 turbo with a T3 turbine housing with a 4 bolt outlet
i am looking for an exhaust adapter from a 4 bolt to a v-band flange
does some one knows where to get one
thanks in advance:thumb:
hi there
after starting the car today and letting it idle for a while
it died and i heard a buzzing noise like the fuelpump was still working
after that i saw smoke coming from the centerconsole
so after shutting everything off
i pulled out my ecu and saw that it was fried
i added some...
like the topic says
when driving the car and accelerating normal there is no problem
but when i floor it and the turbo kicks in the car pulls hard side ways always ripping the steering wheel out of my hands
i allready replaced all motor mounts en bushing(energy suspension bushings kit)
is...
hi guys
when checking the diagnostic codes i got a code 22 ( on a 1G 1990)
this code means crank angle sensor right?
but my cel never came on
is there a way to check this sensor ?
the car runs fine only problem i have that it wont rev unless i adjust the trothle plate
can this sensor...
hi guys
when installing a BW S256 with 70 ar housing on to my exhaust mannifold
(T3 ss autochrome)i had a clearance problem with the turbine housing touching the engine part where the
balance shaft is located
so i added some pics to show what i didwith the turbine housing...
hi guys
i did a search but could not find any info on this
how do i set timing with a c.o.p set up
where do i hook up the timing light cable that normaly connect with sparkplug wire no 1
do i just clamp it on the no 1 coil or what??
thanks.:confused:
hi
just got rid of all the useless vacuum hoses(emission)
and have some guestions about the ports?
do i need to cap off the vacuum ports on the emission purge solenoid and the thermostat
housing or can i leave them open?and what about if i cap of the fuel line that connects to the...
i am replacing my intake mannifold for a race mannifold
so i am not gonna need the intake support the one with the vacuum lines brazed on it
but there is another litle item on the support wich is connected with two wires
(i think a black and a white one) looks like some kind of sensor
can...
can some one tell me what will happen if i leave my tps disconected
what will be the effect on my ecu not getting a signal from the tps?
will this hurt performance?the reason i ask is that i have a 70mm trothle body that needs a 2G tps
and my car is a 1G:confused:
thanks.
hi there
dont know if this is the right place to post this
but can someone give me the partnumber for an ICS for a 1990 dsm GSTis there a site were i can get acces to dsm part numbers :confused:
the manual cd and caps do not cover all the parts
could not find the ics on them
like the topic said
how can i check the o2 sensor cable that leads to the ecu
wich pin to check and what to look for?
my a/f gauge is out and my o2 is 0.01 on the logger with the o2 sensor plugged or unplugged makes no difference so i gues my cable to the ecu is malfunctioning
btw this is...
hi there
after i installed new cams(272/272) and a new timing belt
i cant get the car to idle
i did a boostleak and isc test and they where ok
so i tighten up the trothle cable a bit so now the car idles at 750/850 with the tps at 12,5%
i couldnt get the car to idle with the biss screw...
can some one give me a usefull link where to buy the lower window trim for a 1G
i did a search but the i could not found them on the links provided in the threads
and at mach v they are out of stock
any one else:confused:
satan overhere charges 150 usd .....each:barf:thanks
hi
any one runs this type of turbo on a 2.0 liter engine
i would like to know because i was thinking
instead off upgrading every time lets say from a 16G to a 20G and so on
is it wise too just get a big turbo and drive it first at lower psi untill you got the rest of the supporting mods to...
hi guys
can someone tell me what this is i found it in my oilpan
and yes one of them is a match for size reference(for you funny guys:p )
i checked my rod bearings and they are ok
can this piece of metal come from the main bearings
i am curious about that little round object
thanks.
hi there
just a question about the o2 sensor
are there any aftermarked o2 sensors wich are better than the factory ones ?
or do you guys use the factory o2 sensor on your cars?
thanks,
hi guys
for the moment i am tuning with the maf translator and a non eprom ecu
if i switch to an eprom ecu will there be any benefit from the eprom ecu?
or do they both work the same
thanks.
hi guys
i was changing my lifters today for 3g lifters
now about the hole on the side of the lifter,
when inserting the lifters must the hole on the side of the lifter line up with the hole in the head ?(oil port)
i hope it makes some sense i cant make any pics
t.i.a:thumb:
hi guys
wich brakes can i fit on to my 1990 gst(rear) :confused:
i already have the 3000gt brakes in the front:thumb:
it seems that the rear brakes from the 3000gt do not fit the 1990 gst
is it possibel to swap the rear brakes from another model on to the 1g?(bolt on)
thanks.
hi guys
i have some problems with my ignition when starting the car
first i tought it was the starter but after two different starters still the same problem
when i turn the ignition on i have to wigle the key to start the car
so what i want to do now is make a pushbutton to start the car...
hi guys
i know its possibel to put a 1990 awd(gsx) eprom ecu into a 1990 fwd (gst)
but if the awd ecu is from a ca-mt can it be installed into a federal mt car without any problems:confused:
thanks:thumb:
Hi guys
I have a guestion about the o2 trims
I was tuning the mid section on the maft translator,usin the full throttle tuning guide
It said that when tuning the mid section i have to watch the stft/o2 trims when i roll on the throttle from cruise to a couple of pounds of boost.
If it goes...
Hi there
After doing a leak test i think something went wrong :confused:
After fixing a lot of leaks pressurising the system to 15 psi,the only leak left was air escaping from the breather filter on my valve cover.
So after pluggin up the breathe filter and pressurising the system again i...
Hi there
After a few days playing with the maf translator i still cant get it right.
Can someone explain these numbers to me (i am totaly new at this),
all i know is that the knock is bad :notgood:
This is what the log shows,rpm 3687 - rpm 4000 - rpm 4500 - rpm 5031 -...
hi there
have a evo3 B16 G with ext w/g set up (46mm)
my mbc line is connected to the side port of the w/g the port on the top is left open
i did some searches and this suppose to be the way it has to be hooked up
or should the top one be capped off??
now i dont have any boost at...
hi
got my self a bullseye turbine housing for my evo 3 big 16G turbo
does anyone have this same set up?
the reason i ask is because on the evo 3 the turbine housing is atached with a v-band clamp,
but on the bullseye turbinehousing the evo 3 fits into the turbine housing .
the...
hi guys
i am at the point of putting in my clutch /flywheel/tranny(fwd)1G dsm
i have the act flywheel-act clutch(2600)-clutch fork-pivot bal- extended slave cilinder rod
and a new slave cilinder.
can i put this all together without any problems or did i forget something?
is there anything i...
hi guys
may be one of you can help me out
i am looking for a stainless steel intake mannifold flange
can somebody tell me where to get one?:confused:
thanks for your time.:thumb: